EMIO input
Six gate-pulse logic signals arrive from the EMIO associated with the same control section.
Welcome to Moore Automation Limited
Copy and share this link on social network or send it to your friends
Copy| Product Name | GE IS200ESELH3A ESEL Exciter Selector Board |
| Item NO. | 2940236 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | GE |
| Brand | GE |
| Creation Time | 2026-11-17 |
GE IS200ESELH3A is an H3 Exciter Selector Board in the EX2100 excitation control system. Installed in the control module, it receives six logic-level gate-pulse signals from the corresponding EMIO board and distributes those signals toward Exciter Gate Pulse Amplifier boards in the power-conversion cabinet.
The H3 construction gives GE IS200ESELH3A six bridge-driver outputs. Each cable set carries the selected gate commands to an EGPA, where the logic signal is converted into firing pulses for the six SCRs in a power bridge.
In a redundant control arrangement, two GE IS200ESELH3A boards are driven separately by M1 and M2. Controller C determines which ESEL is active, so only the selected control path sends the required commands to the bridge amplifiers.
| Specification | IS200ESELH3A |
|---|---|
| Brand | GE |
| Functional acronym | ESEL |
| Product type | Exciter Selector Board |
| System | EX2100 excitation control |
| Hardware group | H3 |
| Bridge drivers | Six |
| Input source | Corresponding EMIO board |
| Input signals | Six logic-level gate pulses |
| Output destination | EGPA boards |
| Redundant arrangement | Two ESEL boards, M1 and M2 |
| Active selection | Controller C |
| Mounting area | Control module / EBKP rack |
| Bridge-side location | EGPA in power-conversion cabinet |
| Primary manual | GEI-100456 |
GE IS200ESELH3A bridges the logic-level firing commands in the control rack to the gate-amplifier cables.
Six gate-pulse logic signals arrive from the EMIO associated with the same control section.
The H3 group provides up to six separate cable sets for bridge-driver distribution.
Each path terminates at an EGPA, which generates the firing pulses applied to the six SCR gates in its bridge.
GE IS200ESELH3A participates in the M1, M2 and C selection structure rather than choosing the active controller by itself.
One ESEL is associated with M1 and the second with M2 in a redundant control rack.
Controller C selects which of the two ESEL paths is active for outgoing bridge commands.
The selected ESEL distributes gate commands; the nonselected path does not drive the EGPA cable sets.
GE IS200ESELH3A is the six-bridge-driver group. H1 has one driver and H2 has three, so the complete H3 identification controls output capacity.
GE IS200ESELH3A receives the six logic-level gate commands from the corresponding EMIO and routes them through its driver cable sets to the EGPA boards. Trace that complete EMIO–ESEL–EGPA path rather than checking the SCR gates at the ESEL connector.
GE IS200ESELH3A distributes logic commands to EGPA boards. The EGPA converts them into the actual firing pulses for the six SCRs.
GE IS200ESELH3A boards are associated with M1 and M2, while controller C selects one outgoing ESEL path. A healthy standby path is not expected to drive the EGPA cable sets at the same time as the selected path.
GE IS200ESELH3A sends each bridge-driver cable set to an EGPA board. Confirm the cable lands on the EGPA for the intended bridge before associating it with an SCR firing path.
GE IS200ESELH3A should not be reduced to the ESEL family name. The H3 driver count and the bridge configuration must match the documented control rack.
https://www.mvme.cn
Moore Automation supports mixed-brand automation requirements through a consistent identification process. Exact codes are checked as written, related documents are linked to the request, and changes to quantity or destination remain in the same communication trail.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found