AC input
The CPCA receives 115 V ac control power through the cabinet wiring and its designated connector or terminals.
Welcome to Moore Automation Limited
Copy and share this link on social network or send it to your friends
Copy| Product Name | GE DS200CPCAG1A CPCA Contactor Pilot Card |
| Item NO. | 2940235 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | GE |
| Brand | GE |
| Creation Time | 2026-11-17 |
GE DS200CPCAG1A is a CPCA contactor pilot card used in the EX2000 digital exciter. Its role is to supply the electrical power that closes and holds the contactor; the card does not mechanically force the contactor closed and remains dependent on the cabinet interlock path.
Power entering GE DS200CPCAG1A is 115 V ac, which the card rectifies to approximately 105 V dc for a contactor with a 115 V dc coil. Full coil voltage is applied for pickup and remains present to hold the contactor while the interlock circuit permits operation.
The terminal boundary of GE DS200CPCAG1A includes series-interlock points and auxiliary-contact inputs on 1TB. MACPL is reserved for factory wiring, while RMPL carries daisy-chained control power; the card contains no adjustable hardware for field setting.
| Specification | DS200CPCAG1A |
|---|---|
| Brand | GE |
| Functional acronym | CPCA |
| Product type | Contactor pilot card |
| Control platform | EX2000 digital exciter |
| Input power | 115 V ac |
| Rectified output | Approximately 105 V dc |
| Contactor coil rating | 115 V dc |
| Primary action | Apply power to close and hold contactor |
| Mechanical closure | Not forced by the card |
| Terminal block | 1TB |
| Series interlock | 1TB-1 / 1TB-2 |
| Factory connector | MACPL |
| Control-power connector | RMPL |
| Adjustable hardware | None |
GE DS200CPCAG1A converts cabinet ac control power into the dc level used by the contactor coil.
The CPCA receives 115 V ac control power through the cabinet wiring and its designated connector or terminals.
The board rectifies the ac source to about 105 V dc rather than supplying a separate regulated logic voltage.
The resulting dc is applied to a 115 V dc contactor coil for closing and holding while the command path remains valid.
GE DS200CPCAG1A places the interlock circuit in series with the coil-driving path.
1TB-1 and 1TB-2 provide the connection point for an external interlock in the coil driver circuit.
Additional 1TB points accept normally open auxiliary contacts from the associated contactor.
MACPL is intended for factory wiring; RMPL supports daisy-chained control power between the applicable assemblies.
GE DS200CPCAG1A does not force or latch the contactor mechanically. It applies full electrical voltage to the coil to close and hold the contactor when the control path is complete.
GE DS200CPCAG1A receives 115 V ac and rectifies it to approximately 105 V dc for the 115 V dc contactor coil, so the input and coil sides use different forms of power.
GE DS200CPCAG1A provides 1TB-1 and 1TB-2 as the series-interlock connection in the coil-driving signal path.
GE DS200CPCAG1A contains no adjustable hardware. Its documented function is fixed power conversion and contactor-coil routing.
GE DS200CPCAG1A uses RMPL for factory daisy-chain wiring of control power between the associated contactor pilot circuits.
GE DS200CPCAG1A depends on the series interlock and contactor-coil circuit. Verify the command path, 1TB interlock continuity and coil wiring before treating input power alone as proof of a complete closing circuit.
https://www.mvme.cn
Moore Automation combines product-code checking with organized enquiry communication. Each request can include the manufacturer, exact model, required quantity and destination, reducing ambiguity when several variants share the same functional acronym.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found