Target and probe tip
The 5.26 mm maximum tip faces the conductive target. A change in target distance changes the probe coil response before any signal reaches the cable.
Welcome to Moore Automation Limited
Copy and share this link on social network or send it to your friends
Copy| Product Name | Bently Nevada 330901-00-28-10-02-05 3300 XL NSv 1/4-28 UNF Proximity Probe |
| Item NO. | 2943238 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | BENTLY NEVADA |
| Brand | Bently Nevada |
| Creation Time | 2026-11-20 |
Bently Nevada 330901-00-28-10-02-05 is a 3300 XL NSv 1/4-28 UNF proximity probe in the NSv proximity transducer system. Its sensing tip faces the conductive target, the integral 75 Ω cable carries the probe signal to the matching extension cable, and the Proximitor Sensor converts that change into the voltage used by the connected monitoring channel.
The mechanical code of 330901-00-28-10-02-05 defines a 0.0 in unthreaded section and a 2.8 in overall case, followed by a 1.0 m total probe-and-cable length. The standard miniature coaxial ClickLoc connector is supplied without a connector protector, so the mating joint and any separately selected protection remain distinct from the threaded probe case.
Within the complete 7 m NSv system, 330901-00-28-10-02-05 operates with a nominal incremental scale factor of 7.87 V/mm over the published 1.5 mm linear range. The 1.0 mm recommended gap places the target inside that range, while the -05 ending identifies the multiple-approval option for the exact probe order.
| Attribute | 330901-00-28-10-02-05 |
|---|---|
| Brand | Bently Nevada |
| Product name | 3300 XL NSv 1/4-28 UNF proximity probe |
| Probe base | 330901, without armor |
| Case thread | 1/4-28 UNF-2A |
| Unthreaded length | 0.0 in |
| Overall case length | 2.8 in |
| Total length | 1.0 m |
| Cable impedance | 75 Ω |
| Connector | Miniature coaxial ClickLoc, standard cable |
| Connector protector | Not included in option 02 |
| Probe tip material | Polyphenylene sulfide (PPS) |
| System linear range | 1.5 mm, approximately 0.25 to 1.75 mm |
| Recommended gap | 1.0 mm |
| System scale factor | 7.87 V/mm (200 mV/mil) |
| Agency option | 05, multiple approvals |
The probe does not create a stand-alone monitor signal; each physical section hands the measurement to the next component.
The 5.26 mm maximum tip faces the conductive target. A change in target distance changes the probe coil response before any signal reaches the cable.
The 75 Ω integral cable carries the probe response to the miniature male ClickLoc. The connector is the electrical hand-off to the selected NSv extension cable.
The matching NSv Proximitor Sensor excites the probe circuit and produces a voltage proportional to gap. That output is the signal presented to the monitoring channel.
The two length fields control different parts of the installed probe and must be read together.
The 00 field places the threaded case close to the sensing end; it does not mean the entire case has zero length.
The 28 field sets the overall case length used by the mounting hardware. The unthreaded length must always remain shorter than this case dimension.
The 1 m total-length field includes the attached cable. Cable routing therefore continues beyond the 2.8 in mechanical case boundary.
The published recommended gap for the NSv system used with 330901-00-28-10-02-05 is 1.0 mm, inside its approximately 0.25–1.75 mm linear range.
For 330901-00-28-10-02-05, 00 is a 0.0 in unthreaded length and 28 is a 2.8 in overall case length; they describe different parts of the probe body.
Use 330901-00-28-10-02-05 with the NSv extension-cable and Proximitor Sensor combination that produces the specified complete system length.
Option 02 on 330901-00-28-10-02-05 supplies the standard ClickLoc connector without a connector protector.
The final 05 on 330901-00-28-10-02-05 is the multiple-agency-approval ordering option; the label remains the exact check for the supplied approval markings.
No. The 10 field on 330901-00-28-10-02-05 means the probe and integral cable total 1.0 m; the matching extension cable completes the selected NSv system length.
Moore Automation Limited coordinates industrial automation enquiries around the complete manufacturer and model string. Product-code review, requested quantities and available commercial details are kept on one enquiry record so similar suffixes do not become interchangeable by accident.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found