FluidLoc integral cable
The FluidLoc construction is assigned to the lead leaving the probe case and is selected independently of the M10 × 1 mounting thread.
Welcome to Moore Automation Limited
Copy and share this link on social network or send it to your friends
Copy| Product Name | Bently Nevada 330103-00-06-10-11-05 3300 XL 8 mm M10 × 1 FluidLoc Proximity Probe |
| Item NO. | 2943245 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | BENTLY NEVADA |
| Brand | Bently Nevada |
| Creation Time | 2026-11-20 |
Bently Nevada 330103-00-06-10-11-05 is an unarmored M10 × 1 proximity probe for the 3300 XL 8 mm transducer system. It senses the conductive target, carries that response through its integral cable to the extension-cable connection, and works with the matched Proximitor Sensor that generates the gap-proportional voltage used by the monitor.
For 330103-00-06-10-11-05, the metric mechanical fields identify 0 mm unthreaded length and a 60 mm case, while the 10 field gives a 1.0 m total probe length. Connector option 11 combines FluidLoc cable with a miniature coaxial ClickLoc and connector protector, keeping the fluid-resistant cable construction and joint protection explicit in the full order code.
The complete 8 mm system containing 330103-00-06-10-11-05 has a 2.0 mm linear range, 1.27 mm recommended gap and 7.87 V/mm nominal scale factor. The probe’s -05 ending selects multiple approvals; it does not change the electrical scale or the M10 × 1 mounting geometry.
| Attribute | 330103-00-06-10-11-05 |
|---|---|
| Brand | Bently Nevada |
| Product name | 3300 XL 8 mm metric FluidLoc proximity probe |
| Probe base | 330103, M10 × 1 without armor |
| Unthreaded length | 0 mm |
| Overall case length | 60 mm |
| Total length | 1.0 m |
| Cable option | FluidLoc cable |
| Connector | Miniature coaxial ClickLoc |
| Connector protector | Included with option 11 |
| System linear range | 2.0 mm |
| Recommended gap | 1.27 mm |
| System scale factor | 7.87 V/mm |
| Probe tip material | PPS |
| Case material | AISI 303 or 304 stainless steel |
| Agency option | 05, multiple approvals |
The option 11 field controls both the cable type and the fitted protection around the mating interface.
The FluidLoc construction is assigned to the lead leaving the probe case and is selected independently of the M10 × 1 mounting thread.
The miniature coaxial contacts carry the probe circuit into the extension cable; the connector protector surrounds that joint but is not an electrical contact.
The 330103 base has no metal armor, so the route is defined by the FluidLoc cable itself and the permitted bend and installation clearances.
Mechanical positioning places the sensing face near the target; the matched electronics then use the calibrated portion of the response.
The 06 metric case field corresponds to 60 mm. With 00 unthreaded length, the threaded body remains the primary position reference.
The recommended gap places the probe near the middle of the 8 mm system’s published linear region.
After conversion in the Proximitor Sensor, three-conductor shielded wiring carries the output to the monitor rather than extending the probe’s coaxial circuit directly.
For 330103-00-06-10-11-05, confirm the M10 × 1 mechanical code, FluidLoc option, complete system length, compatible 8 mm extension cable and Proximitor Sensor, and required approval markings.
The 11 connector field in 330103-00-06-10-11-05 specifies FluidLoc cable plus a miniature coaxial ClickLoc with a protector.
The protector supplied with 330103-00-06-10-11-05 surrounds the ClickLoc mating joint between the probe lead and the extension cable.
330103-00-06-10-11-05 has 0 mm unthreaded length, a 60 mm overall case and an M10 × 1 case thread.
In the matched 8 mm system, 330103-00-06-10-11-05 operates with a nominal 7.87 V/mm scale factor over the published 2.0 mm linear range.
No. The 330103 base of 330103-00-06-10-11-05 is the M10 × 1 probe without armor; FluidLoc describes the cable option, not metal armor.
Moore Automation Limited handles enquiries through a named contact who can keep exact model strings, quantities and supporting photos together. The commercial response can then distinguish cable, connector and approval suffixes before quotation information is issued.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found