GE Fanuc IC754CKF15CTD 15-inch QuickPanel Control Starter Kit
Product Description
IC754CKF15CTD is the starter-kit ordering form for a 15-inch QuickPanel Control system. It establishes a complete development-to-panel package under one ordering identity for projects that require the loaded terminal together with the associated setup components, rather than a display-only terminal order.
Within the machine, the terminal combines operator visualization with local control execution. Its embedded operating environment hosts the deployed application, while its communication and removable-media architecture connects the panel with controllers, project-transfer workflows and stored application data.
Technical Specifications
Display
- Display
- 15.1-inch color TFT
- Resolution
- 1024 × 768 pixels
- Color depth
- 24-bit, 16,777,216 colors
- Touch input
- 12-bit resistive touchscreen
Computing
- Processor
- Intel XScale PXA255, 400 MHz
- DRAM
- 64 MB; expandable to 96 MB or 128 MB
- Flash memory
- 64 MB
- Battery-backed SRAM
- 512 KB
- Operating system
- Microsoft Windows CE
Connections
- Ethernet
- Two 10/100Base-T RJ45 ports
- Serial ports
- COM1 EIA-232/EIA-485; COM2 EIA-232
- USB
- Two USB 1.1 ports
- Removable storage
- One Type I/II CompactFlash slot
- Fieldbus expansion
- One expansion slot
Power + installation
- Input voltage
- 12 VDC ±20% or 24 VDC ±20%
- Power
- Less than 60 W
- Panel cutout
- 379.25 × 305.55 mm (W × H)
- Mounting depth
- 70.7 mm
- Bezel
- 398.8 × 323.2 mm (W × H)
- Panel thickness
- 1.6 to 5 mm
- Operating temperature
- 0 to 50°C
- Front protection
- NEMA 4/12/4X; IP65 when correctly mounted
Starter Kit Scope
Loaded control display
The 15-inch QuickPanel Control terminal provides the touchscreen, computing platform, communication ports and local-control hardware.
Engineering software
Proficy Machine Edition is included under the starter-kit ordering identity for application development and transfer.
24 VDC power supply
The kit includes the DC supply item used to energize the terminal during setup and installation.
Ethernet cable
The supplied network cable supports the Ethernet connection used during commissioning and project transfer.
Installation
Install IC754CKF15CTD in a clean, flat panel opening that meets the documented cutout, depth, thickness and ventilation requirements. Complete the mechanical mounting before reconnecting removable media, communication cables or DC power.
Panel Mounting Sequence
- Isolate and clearRemove the CompactFlash card, disconnect all cables and remove the power plug before fitting the terminal.
- Insert the terminalPlace IC754CKF15CTD squarely into the prepared opening without twisting or displacing the bezel gasket.
- Fit 16 clampsHook every mounting clamp into the housing openings distributed along the top, bottom and both sides.
- Tighten evenlyVerify the gasket position, then tighten the clamp screws evenly to 0.3-0.5 Nm without distorting the panel.
- Connect DC powerWire the supplied 24 VDC, 48 W power plug through its three screw terminals, insert it fully and tighten the retaining screws.
First Start and Settings Retention
- Apply DC power and allow the terminal to complete startup.
- Set display brightness and calibrate the stylus or touchscreen.
- Confirm date, time and network settings for the installation.
- Run Backup, then reboot before removing power so the settings are written to flash.
FAQ
Is IC754CKF15CTD the same order as IC754CSF15CTD?
No. IC754CKF15CTD is the starter-kit order, while IC754CSF15CTD identifies the loaded display. The kit adds the listed software, power-supply and Ethernet-cable items.
What should be checked when an IC754CKF15CTD package is offered without its original carton?
Confirm that the loaded terminal, software entitlement and media, 24 VDC supply and Ethernet cable are all present; a matching terminal alone is not the complete kit.
Can IC754CKF15CTD be mounted in an existing 15-inch enclosure opening?
Use the documented cutout dimensions, panel-thickness range, mounting depth and surrounding clearance as the acceptance criteria before reusing the enclosure.
Which project assets should be secured before replacing IC754CKF15CTD?
Preserve the editable Machine Edition project, deployed application, target definition, communication settings, retained data, recipes and license evidence.
Why should IC754CKF15CTD be rebooted after backed-up settings are changed?
Reboot before disconnecting DC power so the saved operating-system settings are written to flash and can be confirmed during the next startup.
WWW.MVME.CN
Moore Automation coordinates industrial automation parts sourcing for current, discontinued and hard-to-find requirements.
Recommended Products
Request Product Information
MANAGERLeonia
EMAILsales@mvme.cn
WHATSAPP+8618030175807
No related record found