Welcome to Moore Automation Limited
|
Copy and share this link on social network or send it to your friends
Copy| Product Name | Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 3300 XL 8 mm ETR Armored Proximity Probes |
| Item NO. | 2931707 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | BENTLY NEVADA |
| Brand | Bently Nevada |
| Creation Time | 2026-11-11 |
Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 are 3300 XL 8 mm Extended Temperature Range proximity probes with 3/8-24 UNF threads and stainless-steel armor. Each probe works with its extension cable and Proximitor Sensor to convert the distance between the probe tip and a conductive target into a proportional voltage signal.
The mechanical bodies of Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 share a 0.0 in unthreaded length and a 2.5 in case, while their calibrated total lengths are 5.0 m and 1.0 m. The length field therefore identifies which probe belongs in each complete transducer system even though the threaded cases have the same dimensions.
Across the 2.0 mm linear range, Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 use the 7.87 V/mm scale factor of the 3300 XL 8 mm system. The recommended 1.27 mm gap places the probe near a -9 VDC operating point, and the armor protects the integral lead between the probe case and its connector.
| Specification | 330192-00-25-50-00 | 330192-00-25-10-00 |
|---|---|---|
| Brand | Bently Nevada | Bently Nevada |
| Product Name | 3300 XL 8 mm ETR Armored Proximity Probes | 3300 XL 8 mm ETR Armored Proximity Probes |
| Country | Not specified | Not specified |
| Thread | 3/8-24 UNF | 3/8-24 UNF |
| Unthreaded length | 0.0 in | 0.0 in |
| Case length | 2.5 in | 2.5 in |
| Total length | 5.0 m | 1.0 m |
| Armor | Stainless-steel armor | Stainless-steel armor |
| Nominal linear range | 2.0 mm | 2.0 mm |
| Average scale factor | 7.87 V/mm | 7.87 V/mm |
| Recommended gap | 1.27 mm / approximately -9 VDC | 1.27 mm / approximately -9 VDC |
| System family | 3300 XL 8 mm ETR | 3300 XL 8 mm ETR |
| Approval field | 00 — approval not required | 00 — approval not required |
Within a complete 3300 XL 8 mm measurement chain, Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 provide the sensing end while the extension cable and Proximitor Sensor complete the calibrated electrical length.
The probe creates the radio-frequency field at the target, the extension cable carries that response, and the Proximitor Sensor produces the conditioned voltage output. All three parts operate as one calibrated system rather than as independent components.
The 5.0 m and 1.0 m probe records represent different total-length configurations. The extension cable and Proximitor Sensor must belong to the same length configuration so the published scale factor and linear range remain applicable.
The probe tip faces a conductive target without physical contact. Changes in target distance alter the conditioned output, allowing the monitor to use the voltage as a shaft-position or vibration measurement input.
The electrical response of Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 is defined by the 3300 XL 8 mm linear range, scale factor and recommended gap, while the ETR construction extends the probe-side temperature capability.
The nominal 2.0 mm linear range is the portion of probe travel used for calibrated displacement measurement. Keeping the operating point within that region preserves the expected relationship between gap and output voltage.
A 1.27 mm mechanical gap corresponds to an operating voltage of approximately -9 VDC. This center-region bias leaves measurable travel in both directions as the target moves toward or away from the probe.
The stainless-steel armor surrounds the integral lead and the ETR design applies to the probe-side assembly. The probe body, cable length and approval field remain part of each complete order record.
Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00 requires this check: Read the `50` versus `10` total-length field and keep the full label with its calibration record; the common case length does not make the probes interchangeable.
For Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00, confirm that the Proximitor Sensor and any extension cable form the same 5.0 m or 1.0 m system length shown by the complete suffix.
The correct approach for Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00: Inspect armor transitions, connector temperature, cable routing and the initial gap before treating the probe as failed.
With Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00, use a generous bend radius, avoid clamping the armor flat and support the lead so vibration is not transferred into the probe body.
Set the documented mechanical gap, verify approximately -9 VDC bias at the recommended gap and compare the trend with the prior baseline. This boundary applies to Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00.
On Bently Nevada 330192-00-25-50-00 / 330192-00-25-10-00, a probe can fit the same 3/8-24 port yet carry the wrong total-length calibration, so the complete suffix and system record must agree.
Moore Automation is a multi-brand industrial automation supplier serving enquiries for current and discontinued control, monitoring and robot components.
For legacy Bently Nevada systems, the company keeps full catalog identities, supporting photographs and available technical records together so similarly named variants remain distinct.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found