A multi-axis motion module for digital servos, encoders, local logic and CAM profiles.
01
Product Description
GE IC694DSM324-BE is a multi-axis motion controller for PACSystems RX3i and compatible Series 90-30 control systems. It coordinates one to four digital servo axes and combines motion sequencing, local logic, CAM profiles and high-speed I/O inside a rack-resident module.
The digital servo path of GE IC694DSM324-BE uses the fiber-optic FSSB interface to communicate with supported beta i amplifiers. Encoder inputs provide master, follower or feedback signals, and a 13-bit analog output supports an additional commanded motion or auxiliary control path.
GE IC694DSM324-BE stores up to ten motion programs and forty subroutines. Position, velocity, registration, electronic gearing and CAM functions operate under the controller project while the module closes its time-critical motion loop independently of the normal PLC scan.
DSM324 motion control with amplifiers, encoders, operator interfaces and programming software.
02
Technical Data
Specification recordVerified product details
Brand
GE
Model
IC694DSM324-BE
Product Name
RX3i / Series 90-30 Motion Controller
Country
Not specified
Controlled Axes
One to four digital servo axes
Servo Interface
FSSB fiber-optic link
Supported Amplifiers
Compatible beta i servo amplifiers
Motion Programs
Up to 10
Subroutines
Up to 40
Motion Functions
Position, velocity, gearing and CAM
Encoder Inputs
Master, follower and feedback use
Analog Output
13-bit command output
High-Speed I/O
Registration and motion-event support
Backplane Supply
5 V DC; approximately 860 mA plus encoder load
Configuration
PAC Machine Edition motion target
03
Monitoring and Control
The DSM324 divides motion work between the PLC project, the rack module and the connected servo amplifiers.
PLANNER
Execute stored motion programs
Motion programs and subroutines define trajectories, waits, gearing and coordinated events without requiring the PLC scan to calculate each servo update. The PLC can start or supervise those programs while the module maintains the motion sequence.
FEEDBACK
Close the position path
Encoder signals report actual or master position to the module, allowing follower, registration and gearing functions to reference real machine movement. Commanded and reported position remain available as separate states for motion supervision.
EVENT I/O
Act on time-critical conditions
High-speed inputs and outputs capture registration marks or trigger motion-related events with timing that is independent of ordinary discrete I/O servicing. This preserves the relationship between a machine event and the active motion profile.
04
Communication and Connectivity
GE IC694DSM324-BE links the backplane control project to servo, encoder, operator and engineering interfaces.
FSSB
Carry digital servo commands
The optical FSSB path connects the DSM324 with compatible beta i amplifiers and transfers command and status data without analog command wiring. The module remains the coordination point for amplifier readiness, axis commands and returned servo state.
BACKPLANE
Exchange commands with the CPU
The RX3i or Series 90-30 controller starts programs, supplies parameters and reads motion status through the module’s rack interface. PLC logic and the motion processor therefore exchange supervisory information without moving the servo loop into the PLC scan.
ENGINEERING
Configure motion and local logic
PAC Machine Edition holds the axis configuration, motion programs, local logic and CAM definitions that determine how the module coordinates the machine. Those elements are downloaded as one motion target so axis identities and program references remain aligned.
05
Product Q&A
What should be checked when GE IC694DSM324-BE follower motion drifts?
For GE IC694DSM324-BE, compare master-encoder counts, gearing ratio, encoder scaling, mechanical slip and the follower error record.
Why can GE IC694DSM324-BE be healthy while an axis is not ready?
GE IC694DSM324-BE module health and axis readiness are separate; check the amplifier state, FSSB path, encoder feedback, drive enable, axis configuration and active motion fault.
How can an FSSB problem be isolated on GE IC694DSM324-BE?
For GE IC694DSM324-BE, inspect optical routing and connector seating, then compare amplifier addresses, power states and the module’s servo-link diagnostics.
Which records help diagnose a GE IC694DSM324-BE axis fault?
For GE IC694DSM324-BE, retain the module LEDs, axis status words, active program step, amplifier alarm, encoder position and the exact project revision.
Why can a registration input be missed on GE IC694DSM324-BE?
GE IC694DSM324-BE registration depends on the correct high-speed input, edge, axis association and timing window; ordinary PLC input mapping does not replace the motion registration path.
What must be saved before changing GE IC694DSM324-BE?
Before changing GE IC694DSM324-BE, save the hardware target, axis parameters, motion programs, subroutines, CAM profiles, local logic and amplifier configuration.
Moore Automation supports installed systems that depend on established motion and rack families. A GE IC694DSM324-BE request can be organized with the exact module identity, surrounding controller information, requested quantity and shipment details so the legacy application remains clear.
Installed-base focusLegacy rack and motion hardware
Record accuracyComplete model and system context
LogisticsProtective packing and shipment coordination
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found