Field signal intake
External terminal blocks bring up to four approved positive-voltage pressure-transducer signals into the I/O module.
Product identity143737-01
Bently Nevada · 3500/77M reciprocating compressor monitoring
Bently Nevada 3500/77M 143737-01 | External-Termination Cylinder Pressure I/O Module
TerminationExternal
Rack positionRear slot
Official product identity and signal path
Model Profile
Bently Nevada 3500/77M 143737-01 is the Cylinder Pressure I/O Module with external terminations for Bently Nevada-approved third-party pressure transducers. It installs behind the 3500/77M monitor in a full-height rear rack slot and forms the field-connection side of the four-channel cylinder-pressure monitoring path.
Each channel routed through Bently Nevada 3500/77M 143737-01 supplies the connected pressure transducer and returns the positive-voltage pressure signal to the front monitor module. The 3500/77M conditions those signals into cylinder-pressure variables, compares active values with configured alert and danger setpoints, and provides buffered channel outputs at the front panel.
Because Bently Nevada 3500/77M 143737-01 is the external-termination version, it is used with the separately ordered external termination blocks and the corresponding 3500 transducer-signal cables. It is not combined with the internal-termination I/O arrangement.
Verified configuration and operating values
Technical Parameters
Technical item3500/77M 143737-01
BrandBently Nevada
Product TypeCylinder Pressure I/O Module
Brand CountryUnited States
System family3500/77M
Monitor order code 3500/77M-04-0004 = external-termination I/O; 00 = no agency approval
Module part number 143737-01Cylinder Pressure I/O Module with external terminations for approved third-party pressure transducers
Termination meaningUse with an external Euro-style or terminal-strip termination block
Transducer typeApproved positive-voltage third-party pressure transducers
Channel count1 to 4 pressure channels through the 3500/77M
Input impedance50 kΩ
Signal-conditioning bandwidth0 to 5.5 kHz
Pressure accuracy at 25 °CWithin ±0.5% of transducer full range
Pressure accuracy over temperatureWithin ±1.0% from −30 to +65 °C
Transducer supply per channel+23.0 ±0.8 Vdc, 24.5 mA current limit
Power consumption7.8 W with transducer supplies at full load
Buffered outputFour front-panel coaxial outputs; short-circuit protected
Buffered output impedance550 Ω
Operating temperature−30 to +65 °C
Storage temperature−40 to +85 °C
Relative humidity95%, non-condensing
I/O module dimensions241.3 × 24.4 × 99.1 mm
I/O module weight0.20 kg
Rack requirementOne full-height rear slot
Required accessoriesExternal termination block and signal cable ordered separately
Four-channel pressure input
Product Functions
Bently Nevada 3500/77M 143737-01 provides the physical input and transducer-power interface behind the 3500/77M cylinder-pressure monitor.
Transducer excitation
The I/O stage supplies each pressure transducer from a current-limited +23 Vdc channel supply while returning the measurement voltage to the monitor.
Rear-rack transfer
The module passes the four pressure channels to the front 3500/77M, which derives pressure variables and alarm decisions from the conditioned signals.
Rack and termination path
System Integration
Bently Nevada 3500/77M 143737-01 is integrated as an external-termination rear I/O stage, not as a standalone pressure monitor.
External field wiring, rear I/O, front monitor
Transducer wiring lands on a separately ordered external termination block, a dedicated cable links that block to 143737-01, and the rear I/O module mates with the 3500/77M front module in the rack.
Select the external termination hardware
Use either the Euro-style or terminal-strip external termination block together with the cable length required by the installation.
Place the I/O module
Install 143737-01 in the full-height rear slot corresponding to the 3500/77M front monitor position.
Keep termination types separate
Do not combine external termination blocks with the internal-termination 143729-01 I/O module; the field hardware must match the I/O version.
Exact-model product questions
Product Help
Why can Bently Nevada 3500/77M 143737-01 arrive without a place to land the field wires?
Bently Nevada 3500/77M 143737-01 is the external-termination rear I/O module; the Euro-style or terminal-strip external termination block and the matching transducer-signal cable are separate order items. Include those items in the bill of material instead of expecting field wires to terminate directly on 143737-01.
What causes a termination mismatch when Bently Nevada 3500/77M 143737-01 is installed behind an existing monitor?
Bently Nevada 3500/77M 143737-01 corresponds to order code 3500/77M-04-00 and cannot use the internal-termination arrangement intended for 143729-01. Confirm the rear I/O part number and the front monitor position together before moving existing terminal hardware.
How should a dead pressure channel through Bently Nevada 3500/77M 143737-01 be traced?
For Bently Nevada 3500/77M 143737-01, check the external termination block, its dedicated cable, the +23 Vdc current-limited channel supply and the positive-voltage transducer return before blaming the front monitor. This follows the actual signal path from the field to the rack.
Why might Bently Nevada 3500/77M 143737-01 work in the rack but still show no connected pressure transducer?
Bently Nevada 3500/77M 143737-01 accepts Bently Nevada-approved positive-voltage third-party pressure transducers, not an arbitrary sensor output. Verify the transducer interface and channel wiring because mechanical installation of the I/O module does not establish electrical compatibility.
What should be checked if Bently Nevada 3500/77M 143737-01 is assigned to the wrong rack position?
Bently Nevada 3500/77M 143737-01 must occupy the full-height rear slot aligned with its 3500/77M front monitor. A rear-slot mismatch breaks the intended channel path even when the module is physically seated in the rack.
What is required when Bently Nevada 3500/77M 143737-01 must monitor machines below the standard speed boundary?
The standard Bently Nevada 3500/77M 143737-01 arrangement has a 60 rpm lower machine-speed limit. Operation down to 30 rpm requires modification 135M8200-01, so the speed requirement must be identified before the monitor configuration is finalized.
Multi-brand automation portfolio
Advantage Brands
Moore Automation
https://www.mvme.cn/Moore Automation supports a broad industrial brand portfolio covering process control, factory automation, machinery monitoring and safety-system hardware. This range allows mixed-brand requirements to be reviewed through one product enquiry.
Core product lines include Bently Nevada and GE monitoring hardware, ABB and Siemens control systems, Schneider Electric and Rockwell Automation platforms, plus Honeywell and Emerson process-control components.
MonitoringBently Nevada and GE
Control platformsABB, Siemens and Schneider Electric
Process automationHoneywell, Emerson and Rockwell Automation
www.mvme.cn
Sixty references across eight industrial brands
Similar Products
- ABBACS310-03E-10A8-2
- Siemens1FK7042-5AK71-1EG0
- GEIC693CMM311T
- OmronCPM2A-40CDR-A
- Schneider Electric140DRC83000
- Mitsubishi ElectricMR-J3-200BN-RJ004U658
- HoneywellTK-IDW161
- MoxaEDS-510A-3GT
- ABBACS310-03U-06A2-4
- Siemens1FT5072-0AC01-Z
- GEIC693CMM311P
- OmronC500-RM201
- Schneider ElectricTBUX297319
- ABBACS320-01E-02A4-2
- Siemens6ES7157-0AC80-0XA0
- GEIC200UEX626-D
- OmronCP1L-L14DR-D
- Schneider ElectricTM202-A00-B00-C00
- ABBACS320-03E-01A2-4
- Siemens6AG4021-0AD11-0CB0
- GEIC695PSD040L
- OmronC200H-DA0002
- Schneider ElectricLXM15HC20N4X
- ABBACS320-03E-08A8-4
- Siemens6ES7647-7BL40-2DB0
- GEIC35L073UCDY10-0
- OmronCJ1W-ID231
- Schneider ElectricTM2DRA16RT
- ABBACS320-03U-07A4-2
- Siemens6SE3210-7CA40
- GEIC695ETM001-HW
- OmronCV500-IC201
- Schneider Electric140AC002000
- ABBACS320-03U-14A6-2+N7558
- Siemens6SL3040-0PA01-0AA0
- GEIC693MDL655K
- OmronCJ1W-PA205R
- Schneider ElectricBMXP342010
- ABBACS350-01-12A6-4
- Siemens6FX8002-2AD00-1BK0
- GEDS2005
- OmronCPM-E3
- Schneider ElectricATV320U55N4B
- ABBACS355-01E-01A2-4
- Siemens6SL32101PE161UL1
- GEDS200RCIAG1
- OmronC500-PS211
- Schneider Electric140DDO35310
- ABBACS355-01E-07A5
- Siemens6AV6580-3BX05-2BX0
- GEIC695CHS012-DA
- OmronCQM1-IPS02
- Schneider Electric140DAI55300
- ABBACS355-01U-04A7-2
- Siemens6ES7531-7KF00-0AB0
- GEIC501BWH0001000S
- OmronC500-LK010-P
- Schneider ElectricTM2-0720-BC
- ABBACS355-03E-01A2-4
- Siemens6SL3202-0AE21-8CA0
Direct product enquiry channels
Sales Assistance
Moore Automation
Connect with our team
Use the channels shown here for technical product and purchasing enquiries.
ManagerLeonia
Emailsales@mvme.cnWhatsApp+86 180 3017 5807
No related record found