Bently Nevada · 3300 XL 8 mm330102Armored Proximity Probe

Exact ordering configuration

Bently Nevada 330102-00-32-10-02-00 Armored Proximity Probe

Name: Bently Nevada 330102-00-32-10-02-00 Armored Proximity Probe
Brand: Bently Nevada
SKU: 2931685
Price: 1 USD
Availability: InStock

A 1.0 m armored 3300 XL 8 mm probe with a 3/8-24 UNF case and miniature ClickLoc coaxial connector for shaft-position and vibration measurement.

Product Introduction

Bently Nevada 330102-00-32-10-02-00 is an armored standard-mount probe in the 3300 XL 8 mm proximity transducer family. It forms the sensing end of a complete proximity system, observing the distance between the probe tip and a conductive target so the associated Proximitor sensor can provide a voltage that represents static position and dynamic motion.

The ordering string defines the installed hardware rather than a generic 3300 XL assembly. Code 330102 identifies the 3/8-24 UNF probe with armor; 00 specifies zero unthreaded length, 32 specifies a 3.2 inch case, 10 specifies 1.0 metre total length, 02 selects the miniature coaxial ClickLoc connector with standard cable, and 00 indicates that a separate approval selection is not required.

Because the total probe length is 1.0 metre, Bently Nevada 330102-00-32-10-02-00 is used without a separate extension cable in a 1 metre system. The probe, connector and Proximitor sensor must remain electrically compatible as one system, while the armored lead protects the cable mechanically without replacing correct routing, clamping or connector sealing.

Bently Nevada 330102 armored 3300 XL 8 mm proximity probe dimension figure

Technical Information

Brand	Bently Nevada
Model	330102-00-32-10-02-00
Product name	3300 XL 8 mm Armored Proximity Probe
Country	United States
Probe family	3300 XL 8 mm
Mounting style	Standard mount
Case thread	3/8-24 UNF-2A
Cable protection	Armored
Unthreaded length	0.0 in
Overall case length	3.2 in
Total probe length	1.0 m
Connector	Miniature coaxial ClickLoc
Cable type	Standard cable
System arrangement	1 m probe; no extension cable
Approval option	Approvals not required

Signal Processing

The measurement chain around Bently Nevada 330102-00-32-10-02-00 depends on the mechanical gap, the electrical match and the integrity of the coaxial path working together.

Target gap

Probe tip position sets the operating point

The 8 mm tip faces a conductive target across a controlled gap. Static movement changes the average output while shaft vibration appears as the changing component, so a correct initial gap leaves usable range in both directions instead of placing the signal near an electrical limit.

Matched system

Probe and Proximitor behave as one circuit

The 1.0 m lead is part of the calibrated transducer length. Substituting another cable arrangement changes the electrical system, which is why Bently Nevada 330102-00-32-10-02-00 is paired with the compatible 1 m system input rather than extended with an extra cable.

Coaxial path

Connector condition protects signal quality

The miniature ClickLoc connection carries a low-level proximity signal. A loose coupling, contamination or damaged dielectric can introduce noise or an unstable bias voltage, so the connector is seated squarely, kept clean and supported away from repeated bending.

Installation and Maintenance

Mechanical fit and cable handling determine whether Bently Nevada 330102-00-32-10-02-00 can hold a repeatable gap after the machine returns to service.

Check insertion depth before tightening

Confirm that the 3.2 inch case clears the bracket and that zero unthreaded length suits the mounting geometry. Thread the case without forcing the tip toward the target, set the working gap from a live voltage reading, then secure the adjustment so vibration cannot move it.

Use armor as protection, not as a pulling point

Form generous bends and clamp the armored lead where machine motion cannot rub it against sharp edges. Keep the coaxial route separated from high-current switching conductors and do not twist the probe body by pulling on the armor or connector.

Diagnose the complete loop before replacement

Record the bias voltage at rest, inspect the target surface, confirm connector engagement and compare the dynamic waveform with the channel history. These checks separate a gap shift or cable fault from a monitor or Proximitor problem.

Frequently Asked Questions

Why does Bently Nevada 330102-00-32-10-02-00 show an out-of-range bias after installation?

Bently Nevada 330102-00-32-10-02-00 may be too close to or too far from the target, or the one-metre system may be connected to an incompatible Proximitor input. Verify the mechanical gap from the live voltage, then confirm the complete system length and connector seating before changing the monitor configuration.

Can an extension cable be added to Bently Nevada 330102-00-32-10-02-00?

Bently Nevada 330102-00-32-10-02-00 already provides the full 1.0 m system lead. Adding an extension cable changes the calibrated electrical length and should not be used to solve a routing shortage; select a documented longer system configuration instead.

What should be checked when Bently Nevada 330102-00-32-10-02-00 produces intermittent vibration spikes?

For Bently Nevada 330102-00-32-10-02-00, inspect the ClickLoc coupling, armor termination, cable bends, target surface and route near variable-frequency drive conductors. Compare the raw waveform and bias trend so an electrical discontinuity is not mistaken for real shaft motion.

How should Bently Nevada 330102-00-32-10-02-00 be regapped after machine work?

Regap Bently Nevada 330102-00-32-10-02-00 with the machine secured and the associated channel energized for measurement. Move the threaded case gradually while observing bias voltage, lock the final position, and verify that tightening did not shift the reading.

Why must the complete ordering number be retained for Bently Nevada 330102-00-32-10-02-00?

The suffixes in Bently Nevada 330102-00-32-10-02-00 define case length, total length, connector style and approval selection. Ordering only 330102 can produce a probe that fits the family but not the existing bracket, route or electrical system.

What is the safest first check before replacing Bently Nevada 330102-00-32-10-02-00?

Before replacing Bently Nevada 330102-00-32-10-02-00, document the stationary bias, inspect the target and connector, and test the channel with a known-compatible loop where site procedures allow. This avoids replacing a healthy probe when the fault is a shifted bracket, damaged connector or downstream electronics.

Shipping Services

Moore Automation

https://www.mvme.cn

Moore Automation prepares industrial automation shipments around the exact model, quantity and destination. Identification details stay with the commercial record so receiving teams can compare the delivered label with the requested Bently Nevada configuration.

For Bently Nevada 330102-00-32-10-02-00, compact probe packaging, protected connector support and destination documentation are coordinated before dispatch, reducing avoidable handling stress on the armored lead.

Route reviewDestination and delivery method checked

Protected packingTip and connector kept supported

Record continuityFull ordering string retained

Air freight image representing Moore Automation shipping services

Selected Products

Contact & Enquiry

Discuss this exact probe configuration

ManagerLeonia

Emailsales@mvme.cn

WhatsApp+86 180 3017 5807

Product Name	Bently Nevada 330102-00-32-10-02-00 Armored Proximity Probe
Item NO.	2931685
Weight	0.1 kg = 0.2205 lb = 3.5274 oz
Category	BENTLY NEVADA
Brand	Bently Nevada
Creation Time	2026-11-11

Bently Nevada 330102-00-32-10-02-00 Armored Proximity Probe Item NO.: 2931685