PACSystems RX3i · Universal Analog Input

IC695ALG600-DD

IC695ALG600-DD provides eight general-purpose input channels and two cold-junction compensation channels for PACSystems RX3i control systems.

Each channel is configured in Proficy Machine Edition for voltage, current, thermocouple, RTD or resistance measurement. The module must be installed in an RX3i Universal Backplane.

Official Features

Built for configurable field measurement

Software configuration

No module jumpers are required.

Automatic calibration

Autocalibration runs at power-up.

Channel diagnostics

Fault, alarm, overrange and underrange reporting is available per channel.

Hot insertion

The module supports hot insertion and extraction.

Input monitoring

Open-circuit detection is available for most input types; RTD short-circuit detection is supported.

User scaling

Floating-point scaling is configurable for the application.

Local indication

Module OK, Field Status and TB LEDs show operating condition.

Terminal-block detection

Insertion and removal status is monitored by the module.

Product Specifications

IC695ALG600-DD technical data

All principal electrical, channel and configuration parameters are consolidated in this section.

Product typeUniversal analog input module

PlatformPACSystems RX3i

General-purpose inputs8

CJC channels2

Thermocouple typesB, C, E, J, K, N, R, S, T

RTD wiring2-wire, 3-wire and 4-wire

Voltage ranges±10 V, 0–10 V, 0–5 V, 1–5 V, ±50 mV, ±150 mV

Current ranges±20 mA, 0–20 mA, 4–20 mA

Input resolution11 to 16 bits, depending on range and filter frequency

Conversion methodSigma-delta

Configurable filters8, 12, 16, 40, 200 and 1000 Hz

Per-channel acquisition127 ms at 8 Hz to 10 ms at 1000 Hz

5 VDC backplane load300 mA maximum

3.3 VDC backplane load320 mA maximum

Power dissipation5.4 W maximum

Calibrated accuracy at 25°CBetter than 0.1% of range, except 10 Ω copper RTD

Input impedanceGreater than 1 MΩ for TC, voltage and RTD

Current input resistance249 Ω ±1%

Maximum overvoltage±14.5 VDC continuous

Maximum overcurrent28 mA continuous

RTD cable impedance25 Ω maximum

RTD wire length1000 ft maximum with 1 ms settling time

Calibration interval12 months typical

Module firmwarePrimary 1.14; Boot 1.10

CPU requirementRX3i CPU firmware 2.80 or later

Programming softwareProficy Machine Edition 5.0 SP1A with LD-PLC Hotfix 1 or later

Supported terminal blocksIC694TBB032, IC694TBB132, IC694TBS032 or IC694TBS132; ordered separately

CJC sensor setIC695ACC600

Official Technical Diagrams

Module layout and field connections

IC695ALG600-DD front-panel layout redrawn from GE Product Information GFK-2348J. Indicator and channel positions are shown for identification.

Connection arrangements redrawn from the official Module Wiring and Installing CJC Sensors sections of GFK-2348J. Use the complete terminal assignment table in the manual during installation.

Product Technical Images

Functional signal overview

IC695ALG600-DD functional signal overview. Embedded technical illustration for system orientation only; it is not a terminal wiring diagram or dimensional drawing.

Official Discontinuation & Replacement Info

Lifecycle record

Lifecycle statusNo official discontinuation notice published

Discontinuation dateNot published

Last-time buy / support endNot published

Designated replacementNo one-for-one replacement published

For replacement of an installed module, match the complete catalog and revision marking, terminal block, channel configuration, sensor wiring, scaling, alarms and CPU/PME compatibility before commissioning.

Request an IC695ALG600-DD quotation
Send the installed revision, quantity and terminal-block requirement.

Manager: Leonia
sales@mvme.cn

WhatsApp
+86 18030175807

Applications

Universal field measurement in RX3i systems

Process instrumentation

Acquisition of voltage and current signals from transmitters used for pressure, flow, level and other process variables.

Temperature monitoring

Thermocouple and RTD measurement for machinery, process equipment and production assets.

Resistance measurement

Direct resistance inputs where the configured range and field wiring match the supported channel setup.

Procurement FAQ

Five checks before ordering

What information should be supplied with an inquiry?

Provide the complete catalog marking, hardware revision, required quantity and whether a matching terminal block is needed.

Does the terminal block come with the module?

The removable terminal block is ordered separately. Confirm the installed terminal-block type before placing an order.

What should be recorded before removing an installed module?

Retain the existing hardware configuration, channel assignments, scaling, alarms and field-wiring records for commissioning.

What must be checked when replacing an earlier revision?

Verify the full revision suffix, RX3i CPU firmware, PAC Machine Edition version, terminal block and project configuration.

Is a one-for-one successor identified?

No designated one-for-one replacement is published. Replacement planning must be based on the installed system configuration and compatibility requirements.

Industrial automation model index

Column A	Column B	Column C
EX-P-0600	IC200MDL640F	6ES7193-4CB30-0AA0
ABB 281844-020-03	760ATC	KL1722
DDLE802	M1032-61635	KL3454
CMDSLCZBU	M1032-61602	EEID4A EA900102
LBB4443/00	M1032-61605	400-P0W
253-TVLW-NXHG-C5-BD	WAP125-A-K9-BR	5WG1 528-1AB02
IRM-S01AN-B	TN1P4PA62A D8AW2	140011
CM485	181B0729 SPR-CMB21640	2N 9151002
MOD2-2R	ABB TU510-A3T 1SAP210800R0001	ASY0001241
ABB TU532 1SAP217000R0001	ABB TU516-H 1SAP215000R0001	5WG1 523-1AB02
MFM383A-C-CE	ABB TU542-H 1SAP215200R0001	A4 51 84 Rex2000 D42
E1242	TP-RDR-100A	PXC100.D
AS-F9165UA-02	OEM750X-M2	6499-11-00
IO44E01KNX	TXA112	HT-9001-URW
ABB DO524 1SAP240700R0001	AM 503	MX-OPT-F2.0-L65-L25
MDM021	4930275	IC695ALG608
L24734-F655-A5	ABB G4001 2TME050080N0001	IC695ALG616
2CDG110064R0011	1SBN153510R8106 ZA75	IC695ALG626
LGAN-WF100	TWDXCAISO	IC695ALG628
CP1E-NA20DT1-D CP1W-8ET1	DMC-4K-HD	IC695ALG704

Product Name	GE IC695ALG600-DD RX3i Universal Analog Input Module
Item NO.	2895936
Weight	0.15 kg = 0.3307 lb = 5.2911 oz
Category	GE
Brand	GE
Creation Time	2026-08-12

GE IC695ALG600-DD RX3i Universal Analog Input Module Item NO.: 2895936