Prepare the M10 × 1 location
Confirm available insertion depth, maintain the 15 mm thread-engagement boundary and keep the 240 mm case clear of interference.
Product identity330910
Bently Nevada · armored 3300 XL NSv probe
Bently Nevada 330910-00-24-10-01-CN | Armored 3300 XL NSv M10 × 1 Probe
Case240 mm
ApprovalCN
Official product identity and signal path
Product Profile
Bently Nevada 330910-00-24-10-01-CN is the armored M10 × 1 execution of the 3300 XL NSv proximity probe. It provides the machine-side eddy-current sensing field for shaft-position or vibration measurement while stainless-steel armor protects the probe cable leaving the case.
The complete order code of Bently Nevada 330910-00-24-10-01-CN selects a 0 mm unthreaded section, a 240 mm overall case and a one-metre total lead. DD 01 adds the standard ClickLoc connector protector, and CN retains the country-specific China approval selection on the exact product record.
A matching NSv extension cable and Proximitor Sensor complete Bently Nevada 330910-00-24-10-01-CN as a calibrated transducer path. The probe produces the target-dependent response, the cable preserves the selected system length and the Proximitor converts the signal into the output received by the monitor.
Verified configuration and operating values
Performance Specifications
Technical item330910-00-24-10-01-CN
BrandBently Nevada
Product TypeArmored 3300 XL NSv proximity probe
Brand CountryUnited States
System family3300 XL NSv
Base code 330910M10 × 1 thread; with flexible stainless-steel armor
AA 00 — unthreaded length0 mm
BB 24 — overall case length240 mm
CC 10 — total probe length1.0 m
DD 01 — connector and cableClickLoc with connector protector; standard cable
EE CN — approval optionChina hazardous-area approval option
Probe tip diameter5.26 mm
Linear range1.5 mm (60 mil)
Recommended gap1.0 mm (40 mil)
Scale factor7.87 V/mm (200 mV/mil), +12.5%/−20%
Frequency response0 to 10 kHz, +0/−3 dB typical
Probe case materialAISI 304 stainless steel
Cable armorFlexible stainless steel
Probe temperature−52 to +177 °C
Maximum M10 thread engagement15 mm
Recommended M10 case torque11.3 N·m
System supply−17.5 to −26 Vdc; 12 mA maximum
Armored long-case mounting
Installation Highlights
Installation of Bently Nevada 330910-00-24-10-01-CN must preserve both the long probe geometry and the protected cable path.
Gap the active tip
Position the 5.26 mm tip at the required working gap against the conductive target, then secure the body without twisting the probe lead.
Support armor and connector
Route the armored lead above its minimum bend radius, support it independently of the probe tip and fully seat the protected ClickLoc connection.
CN approval record
Safety and Compliance
The CN suffix on Bently Nevada 330910-00-24-10-01-CN is part of the exact certified execution and must remain attached to the installed model record.
Keep approval, label and installation together
The country-specific approval selection does not replace the need to follow the product marking, associated installation drawing and connector-protection requirements supplied with the probe.
Confirm the CN nameplate
Match the complete 330910-00-24-10-01-CN identifier before installation or replacement.
Observe approved wiring conditions
Use the specified NSv cable and Proximitor path and maintain the environmental protection of each connector.
Document the installed configuration
Record the full suffix and the connected system components so the approval execution remains traceable.
Exact-model product questions
Technical Questions
Why can Bently Nevada 330910-00-24-10-01-CN still suffer cable damage even though it is armored?
Bently Nevada 330910-00-24-10-01-CN uses flexible stainless-steel armor for mechanical protection, but the armor still needs a controlled route and strain relief. Avoid forcing the one-metre lead through a bend or allowing machine movement to pull on the ClickLoc joint.
What should be checked if Bently Nevada 330910-00-24-10-01-CN cannot reach the required target position?
Bently Nevada 330910-00-24-10-01-CN has a 240 mm case, zero unthreaded length and a 15 mm maximum M10 × 1 thread engagement. Review the mounting boss and available reach rather than compensating by exceeding the engagement boundary.
Why does the connector protector on Bently Nevada 330910-00-24-10-01-CN not remove the need to inspect the ClickLoc joint?
DD 01 on Bently Nevada 330910-00-24-10-01-CN adds a connector protector around the standard ClickLoc interface. It protects the mated joint from the environment but does not correct incomplete mating, contamination or cable tension.
How can a customer avoid a system-length mismatch with Bently Nevada 330910-00-24-10-01-CN?
Bently Nevada 330910-00-24-10-01-CN contributes a one-metre probe length to the NSv chain. Select the extension cable and Proximitor Sensor for the same complete electrical length; do not choose them solely because their connectors fit.
What should be recorded before replacing Bently Nevada 330910-00-24-10-01-CN at a China-approved site?
Record the complete Bently Nevada 330910-00-24-10-01-CN identifier, nameplate approval markings and installed cable configuration. CN is the China hazardous-area approval option, so dropping the suffix can change the compliance basis of the replacement.
What can cause Bently Nevada 330910-00-24-10-01-CN to show an offset immediately after tightening?
Tightening the long M10 × 1 body of Bently Nevada 330910-00-24-10-01-CN can shift the working gap if the probe is not locked while square to the target. Recheck the approximately 1.0 mm reference gap after securing the case.
International shipment support
Packaging and Logistics
Moore Automation
https://www.mvme.cn/Moore Automation coordinates packaging and delivery around the product type, order quantity and destination. Sensitive automation hardware is prepared for transport with protection suited to the item and the planned shipping route.
Carrier, tracking and destination details remain connected to the product record after dispatch. This gives the customer one reference for the hardware ordered and the shipment carrying it.
Protective packingPrepared for the specific hardware
Shipment recordsProduct and tracking details connected
Global destinationsInternational delivery coordination
www.mvme.cn
Sixty references across eight industrial brands
Compatible Products
- ABBACS320-03E-10A8-2
- Siemens1FT6062-1AF71-3EH1
- GEIS220PPDAH1B
- OmronCJ1W-OD202
- Schneider Electric140CRA93100C
- Mitsubishi ElectricAJ71QE71-B5
- HoneywellCC-TAIX01
- MoxaEDS-308
- ABBACS320-03U-08A8-4
- Siemens1FT6034-1AK71-4EB1
- GEIs200tbtch1b
- OmronCJ1W-OD213
- Schneider Electric140DAI55300C
- ABBACS320-03U-19A
- Siemens6ES5710-8MA11
- GEIS200TVBAH2ACC
- OmronC200H-BC051
- Schneider ElectricTM221ME32TK
- ABBACS350-03E-02A4-4
- Siemens6ES7142-1BD40-0XB0
- GEIC694MDL930D
- OmronCJ1W-CIF21
- Schneider ElectricTM2DDI16DT
- ABBACS355-01E-02A4-2
- Siemens6FX5002-8QN11-1AH0
- GEIC35L146UCDY10-0
- OmronNX-V60KA
- Schneider ElectricTSXSUP40
- ABBACS355-01E-09A8
- Siemens6SE6440-2UD23-0BA1
- GEIC31227G01
- OmronC500-IM212
- Schneider Electric140AVO02000
- ABBACS355-01U-06A7-2
- Siemens6SL3162-0AF00-0AA1
- GEIC200MDL650
- OmronNX-ID4442
- Schneider ElectricBMXEHC0800
- ABBACS355-03E-01A9-4
- Siemens6ES7316-2AG00-0AB0
- GEIC600BF904K
- OmronC200HE-CPU11
- Schneider ElectricBMXDDO1602H
- ABBACS355-03E-03A5
- Siemens6ES7136-6RA00-0BF0
- GEIC677DBM442-CA
- OmronCJ1W-ID261
- Schneider Electric140XBP00600
- ABBACS355-03E-05A6-4+J404
- Siemens6ES7288-2DT32-0AA0
- GEIC693PWR321T
- OmronCPM2A-20CDR-D
- Schneider ElectricBMXP341000
- ABBACS355-03E-08A8-4
- Siemens6ES7331-7KF02-0AB0
- GEIC330-18S-01-DC24
- OmronCS1W-SCB41
- Schneider ElectricTM2-1020-SN
- ABBACS355-03E-09A8-2
- Siemens1FK7101-2AF71-1RH0
Direct product enquiry channels
Request a Quote
Moore Automation
Connect with our team
Use the channels shown here for technical product and purchasing enquiries.
ManagerLeonia
Emailsales@mvme.cnWhatsApp+86 180 3017 5807
No related record found