Bently Nevada3300 XL NSv Proximity Transducer System

Bently Nevada 330904-00-05-05-01-00 / 330904-00-05-05-01-IN | 3300 XL NSv M8×1 Armored Proximity Probes

Name: Bently Nevada 330904-00-05-05-01-00 / 330904-00-05-05-01-IN | 3300 XL NSv M8×1 Armored Proximity Probes
Brand: Bently Nevada
SKU: 2929821
Price: 1 USD
Availability: InStock

Record01

Product Introduction

Bently Nevada 330904-00-05-05-01-00 / 330904-00-05-05-01-IN identifies M8×1 armored NSv probes with the same 0.5 m lead and ClickLoc connector/protector arrangement. They belong to the compact-target 3300 XL NSv system.

The 00 and 05 mechanical fields set zero unthreaded length and a 50 mm case. Stainless-steel armor protects the attached lead where the route is exposed, while the M8×1 case provides the metric mounting interface at the machine.

The final suffix separates the two requested records and must remain visible throughout the enquiry. The common mechanical and cable facts can be compared together, but the 330904-00-05-05-01-00 / 330904-00-05-05-01-IN suffixes should not be treated as interchangeable approval labels without project confirmation.

Bently Nevada NSv M8 by 1 armored standard-mount probes

Data02

Technical Information

Technical item	Suffix 00	Suffix IN
Brand	Bently Nevada
Model	330904-00-05-05-01-00	330904-00-05-05-01-IN
Product Name	3300 XL NSv M8×1 armored proximity probe
Country	United States
System Family	3300 XL NSv
Thread	M8×1
Armor	Stainless-steel armor
Unthreaded Length	0 mm
Overall Case Length	50 mm
Total Probe Length	0.5 m
Connector	Miniature ClickLoc with protector
Cable Type	Standard cable
Final Suffix	00 retained exactly	IN retained exactly; project interpretation required
System Linear Range	1.5 mm
Recommended Gap	1.0 mm
Frequency Response	0 to 10 kHz typical

Focus03

Diagnostics and Protection

Inspect the armored transition

The armored lead protects the cable mechanically, but probe health still has to be separated from wiring and target problems. The guidance below explains how the complete 330904-00-05-05-01-00 / 330904-00-05-05-01-IN record is applied in the installed assembly rather than repeating isolated catalogue values.

Inspect the armored transition

Look for pulled armor, crushed bends or movement at the probe case before testing electrically. Use this checkpoint to separate a mechanical symptom from an electrical fault before replacing 330904-00-05-05-01-00 / 330904-00-05-05-01-IN.

Check the dc gap

A valid supply and abnormal gap voltage can indicate target position, open circuit or shorted cable conditions. Compare the observed state with the installed boundary of 330904-00-05-05-01-00 / 330904-00-05-05-01-IN before disturbing adjacent components.

Keep suffix identity

Record whether the installed probe carries 00 or IN so a mechanical match is not mistaken for a complete record match. Record the test result and restored condition so a repeat fault on 330904-00-05-05-01-00 / 330904-00-05-05-01-IN can be isolated faster.

Focus04

Installation Highlights

Align the M8×1 thread

Metric case preparation and armored-cable routing determine whether the compact probe can hold its designed position. The guidance below explains how the complete 330904-00-05-05-01-00 / 330904-00-05-05-01-IN record is applied in the installed assembly rather than repeating isolated catalogue values.

Path 01

Align the M8×1 thread

Keep the tip perpendicular to the target and avoid side-view metal within the defined clearance. Before closure, record the final position and hardware state for 330904-00-05-05-01-00 / 330904-00-05-05-01-IN.

Identify the exact 330904-00-05-05-01-00 / 330904-00-05-05-01-IN interface before work begins.

Trace the connected mechanical or electrical path.

Record the verified condition before commissioning.

Path 02

Respect armor bend

Support the lead without forcing the armored section into a sharp bend at the case exit. After the mechanical work, verify cable freedom and the measurement gap for 330904-00-05-05-01-00 / 330904-00-05-05-01-IN.

Keep the 330904-00-05-05-01-00 / 330904-00-05-05-01-IN channel and component references together.

Confirm the next device or machine boundary in the path.

Test the completed connection under its intended condition.

Path 03

Protect the ClickLoc joint

Seat and protect the connector before fixing the remaining cable route to the sensor location. Finish with an inspection record that ties the mounted assembly back to 330904-00-05-05-01-00 / 330904-00-05-05-01-IN.

Preserve the complete 330904-00-05-05-01-00 / 330904-00-05-05-01-IN identifier in the work record.

Separate mounting, wiring and signal checks during diagnosis.

Hand over the final result with the installed configuration.

Help05

Frequently Asked Questions

What does the armored construction change for 330904-00-05-05-01-00 / 330904-00-05-05-01-IN?

The armor on 330904-00-05-05-01-00 / 330904-00-05-05-01-IN adds mechanical protection but requires controlled bend radius and support at the case transition. It does not make the connector immune to pulling or contamination.

How should the M8×1 case be aligned for 330904-00-05-05-01-00 / 330904-00-05-05-01-IN?

Mount 330904-00-05-05-01-00 / 330904-00-05-05-01-IN perpendicular to the target, maintain side clearance and avoid using the cable to rotate the probe. Recheck the gap after the locking hardware is secured.

Why must the 00 and IN endings remain visible on 330904-00-05-05-01-00 / 330904-00-05-05-01-IN?

The two complete identifiers in 330904-00-05-05-01-00 / 330904-00-05-05-01-IN represent distinct order records. Keep the suffix with the installed label so a visually similar probe is not treated as the same configuration.

What is the first check after an intermittent signal from 330904-00-05-05-01-00 / 330904-00-05-05-01-IN?

Inspect the armored transition, ClickLoc connection and cable bends on 330904-00-05-05-01-00 / 330904-00-05-05-01-IN; then verify dc gap and target stability. This sequence separates mechanical damage from a sensor or monitor issue.

Can 330904-00-05-05-01-00 / 330904-00-05-05-01-IN be routed tightly beside the machine case?

Only if 330904-00-05-05-01-00 / 330904-00-05-05-01-IN retains its required bend radius and the armor is supported without rubbing. Reserve space for connector access before fixing clamps or conduit.

What details should accompany 330904-00-05-05-01-00 / 330904-00-05-05-01-IN on an enquiry?

Send 330904-00-05-05-01-00 / 330904-00-05-05-01-IN, quantity, installation thread, available cable route and a clear label photograph. Include the target clearance if the probe is being fitted to an existing bracket.

Moore06

Shipping Services

Moore Automation

https://www.mvme.cn

Shipping services coordinate packing information, dispatch details, carrier references and tracking around the confirmed order record. Destination and quantity remain visible without promising a fixed delivery date.

Packing reviewProduct form and route guide preparation.

Dispatch detailsShipment references stay with the record.

Carrier coordinationAvailable tracking details can be communicated.

Destination controlQuantity and destination remain linked.

Catalogue07

Selected Products

Bosch RexrothHMV01.1R-W0065-A-07-NNNN

Woodward9904-575

HoneywellCC-PCNT03

FoxboroRH924ZQ

Bently Nevada3500/33 149992-01

Allen-Bradley5069-L306ERM

ABBPM572

ABBPM582

ABBPM573-ETH-XC

ABBPM583-ETH-XC

ABBPM591-ETH-XC

ABBPM592-ETH-XC

ABBPM595-4ETH-M-XC

Allen-Bradley5069-L320ERMS2

Bently Nevada3500/42M 176449-02

EmersonKJ1501X1-BC1

HIMAF8651X

HoneywellCC-TDOB01

MotorolaMVME6100-0173

Siemens6ES7511-1CK01-0AB0

TRICONEX3401

ABBPM571-ETH

Allen-Bradley1756-L85EP

Bently Nevada3500/70M 176449-09

EmersonKJ3203X1-BA1

Siemens6ES7516-3FN02-0AB0

Bently Nevada3500/77M 143737-01

HoneywellCC-GDOL21

Bently Nevada3500/92 136188-02

ABBDI562

Siemens6ES7513-1RL00-0AB0

Siemens6ES7517-3HP00-0AB0

Siemens6ES7521-1BH10-0AA0

Siemens6ES7521-1FH00-0AA0

Siemens6ES7522-1BH10-0AA0

Siemens6ES7522-1FH00-0AA0

Siemens6ES7523-1BL00-0AA0

Siemens6ES7531-7NF10-0AB0

Siemens6ES7531-7QD00-0AB0

Siemens6ES7532-5HF00-0AB0

Bently Nevada330701-00-10-10-02-00

Bently Nevada330705-02-18-10-02-00

Siemens6ES7552-1AA00-0AB0

ABBTU531

Bently Nevada2300/20

Siemens6ED1052-1MD08-0BA2

ABBBRC100 / SPBRC100

Bently Nevada991-06-50-01-00

Siemens6ED1055-1MB00-0BA2

ABBCI857K01

Bently Nevada60R/CHA03-02-00

Siemens6GK7177-1MA20-0AA0

ABB07KT93

ABBTP830

ABBTB852

Bently Nevada330851-02-000-080-10-00-00

Bently Nevada21000-34-10-20-058-04-02

Bently NevadaCOMMTEST220

Bently Nevada330106-05-30-10-02-IN

Bently Nevada330500-01-IN

Contact08

Contact & Enquiry

Moore AutomationSend the complete model and requested quantity.

ManagerLeonia

Emailsales@mvme.cn

WhatsApp+86 180 3017 5807

Product Name	Bently Nevada 330904-00-05-05-01-00 / 330904-00-05-05-01-IN \| 3300 XL NSv M8×1 Armored Proximity Probes
Item NO.	2929821
Weight	0.1 kg = 0.2205 lb = 3.5274 oz
Category	BENTLY NEVADA
Brand	Bently Nevada
Creation Time	2026-11-04

Bently Nevada 330904-00-05-05-01-00 / 330904-00-05-05-01-IN | 3300 XL NSv M8×1 Armored Proximity Probes Item NO.: 2929821