Radial vibration
The probe can observe shaft-to-bearing relative motion when installed in the defined NSv geometry.
Welcome to Moore Automation Limited
Copy and share this link on social network or send it to your friends
Copy| Product Name | Bently Nevada 330901-00-32-10-02-05 3300 XL NSv Probe |
| Item NO. | 2911781 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | BENTLY NEVADA |
| Brand | Bently Nevada |
| Creation Time | 2026-09-29 |
Restricted shaft geometry is the operating context for Bently Nevada 330901-00-32-10-02-05, a 1/4-28 UNF probe in the 3300 XL NSv Proximity Transducer System. Its compact tip establishes the non-contact sensing field at a small target, and the connected NSv extension cable and Proximitor Sensor translate gap change into the voltage used by the monitor.
Unlike an armored model, 330901-00-32-10-02-05 has an unarmored 1.0 m standard cable and a miniature ClickLoc connector without a protector. The case is 3.2 in long with zero unthreaded length; those mechanical fields determine how the probe sits in the mounting location while the matched NSv system provides a 1.5 mm linear measurement range.
| Technical Item | 330901-00-32-10-02-05 |
|---|---|
| Brand | Bently Nevada |
| Product Type | Unarmored NSv proximity probe |
| System | 3300 XL NSv Proximity Transducer System |
| Probe Thread | 1/4-28 UNF |
| Armor | Not included |
| Unthreaded Length | 0.0 in |
| Overall Case Length | 3.2 in |
| Total Probe Length | 1.0 m (39 in) |
| Connector | Miniature coaxial ClickLoc |
| Connector Protector | Not included |
| Cable Type | Standard cable |
| Agency Option | Multiple approvals |
| System Linear Range | 1.5 mm (60 mils) |
| Recommended Gap | 1.0 mm (40 mils) |
| System Scale Factor | 7.87 V/mm (200 mV/mil), +12.5%/-20% |
| Frequency Response | 0 to 10 kHz, +0/-3 dB typical |
| Flat Target Diameter | 8.9 mm minimum; 13 mm recommended minimum |
Bently Nevada 330901-00-32-10-02-05 supports the NSv measurements explicitly defined for small targets and constrained mounting areas.
The probe can observe shaft-to-bearing relative motion when installed in the defined NSv geometry.
A probe facing the shaft end can follow position change within the 1.5 mm system range.
The NSv system also supports tachometer, zero-speed and Keyphasor measurement arrangements.
The response limits around 330901-00-32-10-02-05 link target diameter, nominal gap and probe spacing to signal accuracy.
The flat target requires 8.9 mm minimum diameter, with 13 mm recommended.
A 1.0 mm gap places the target inside the 0.25 to 1.75 mm linear region.
Long field wiring can roll off the high-frequency response between the Proximitor Sensor and monitor.
No. Connector option 02 supplies the ClickLoc connector and standard cable without the protector.
No. The 330901 base is the 1/4-28 UNF probe without armor.
It sets the overall case length to 3.2 inches. The preceding 00 separately sets the unthreaded length to zero.
The published minimum flat-target diameter is 8.9 mm. A smaller target is outside the stated target-size condition and can change the response.
The cable after the Proximitor Sensor adds electrical loading to the output path. At long lengths, the upper-frequency response can roll off even though the probe cable itself remains 1.0 m.
Moore Automation handles enquiries across established industrial automation and condition-monitoring brands. The supplied manufacturer name and complete catalog number remain paired throughout quotation review.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found