Gap-dependent response
Target motion changes the probe's eddy-current field. The matched extension cable carries that impedance change to the Proximitor Sensor, which produces the monitor-side voltage.
Welcome to Moore Automation Limited
Copy and share this link on social network or send it to your friends
Copy| Product Name | Bently Nevada 330901-00-24-10-11-05 / 330901-00-30-10-11-05 NSv Proximity Probes |
| Item NO. | 2929791 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | BENTLY NEVADA |
| Brand | Bently Nevada |
| Creation Time | 2026-11-04 |
Two 1/4-28 UNF NSv probes with 2.4 and 3.0 inch cases, a one-metre FluidLoc lead and protected ClickLoc termination.
Bently Nevada 330901-00-24-10-11-05 / 330901-00-30-10-11-05 are 3300 XL NSv proximity probes that sense shaft position or vibration inside a matched NSv transducer system. Their 1/4-28 UNF cases mount at the machine, while the connected extension cable and Proximitor Sensor convert probe impedance into the voltage used by the monitor.
For mechanical reach, Bently Nevada 330901-00-24-10-11-05 / 330901-00-30-10-11-05 provide 2.4 and 3.0 inch overall cases with no unthreaded tip section. Both carry a 1.0 m FluidLoc coaxial lead to a ClickLoc connector with protector, so the case code changes insertion reach without changing the connection method.
During installation, Bently Nevada 330901-00-24-10-11-05 / 330901-00-30-10-11-05 require the selected case to remain clear of target contact through the full machine movement. Nearby probes, counterbores and small targets can alter the field; the completed NSv chain is therefore gapped and checked after the final mechanical position is locked.
| Technical item | 330901-00-24-10-11-05 | 330901-00-30-10-11-05 |
|---|---|---|
| Brand | Bently Nevada | |
| Product name | 3300 XL NSv proximity probe | |
| Country | United States | |
| Probe execution | 330901; 1/4-28 UNF; without armor | |
| Unthreaded length | 00 = 0.0 in | |
| Overall case length | 24 = 2.4 in (61 mm) | 30 = 3.0 in (76 mm) |
| Total probe length | 10 = 1.0 m (39 in) | |
| Connector and cable | 11 = ClickLoc, protector, FluidLoc | |
| Agency approval | 05 = multiple approvals | |
| Linear range | 1.5 mm (60 mil) | |
| Probe tip diameter | 5.26 mm | |
| Nominal scale factor | 7.87 V/mm (200 mV/mil) | |
| Frequency response | 0 to 10 kHz typical system response | |
| Cable construction | 75 Ω coaxial, FEP insulated | |
Bently Nevada 330901-00-24-10-11-05 / 330901-00-30-10-11-05 behave as the target-facing part of a calibrated NSv chain rather than as independent voltage-output sensors.
Target motion changes the probe's eddy-current field. The matched extension cable carries that impedance change to the Proximitor Sensor, which produces the monitor-side voltage.
The small NSv tip suits restricted mounting areas, but counterbore clearance, target diameter and nearby probe fields remain part of the installed measurement geometry.
The two probes use the same one-metre FluidLoc lead and protected ClickLoc termination. Their operating difference is mechanical reach, not a different scale-factor path.
Case selection and final gap verification are the two installation decisions that distinguish these Bently Nevada NSv probes.
Choose the 2.4 or 3.0 inch body after measuring the mounting face-to-target distance and the clearance needed for the connector and lead.
Route the coaxial cable with a smooth bend and independent support. Keep clamp force away from the cable jacket and connector transition.
Connect the correct NSv extension cable and Proximitor Sensor, establish gap voltage, secure the case, then repeat the voltage check through the machine's expected movement.
Use Bently Nevada 330901-00-24-10-11-05 for a 2.4 inch case or Bently Nevada 330901-00-30-10-11-05 for a 3.0 inch case after measuring mounting reach and connector clearance.
The field of Bently Nevada 330901-00-24-10-11-05 depends on target diameter, counterbore geometry and nearby probes. Verify the installed target and clearances before attributing the change to the probe.
Code 11 gives Bently Nevada 330901-00-30-10-11-05 a ClickLoc connector with protector and a FluidLoc cable execution.
No. Bently Nevada 330901-00-24-10-11-05 is one element of the NSv chain; the matched extension cable and Proximitor Sensor are needed to deliver the conditioned voltage.
Recheck the locked case position, bend radius, independent cable support and conditioned gap voltage for Bently Nevada 330901-00-30-10-11-05.
Bently Nevada 330901-00-24-10-11-05 and 330901-00-30-10-11-05 do not require different settings because of case length alone. Confirm the complete probe, extension cable and Proximitor Sensor record before applying the monitor configuration.
Moore Automation can keep packing references, destination details and carrier information attached to the same industrial-part enquiry. Tracking information is shared when supplied by the selected carrier.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found