Probe excitation and return
The Proximitor Sensor drives the matched 3300 XL 8 mm probe and receives the response that changes with target-to-probe distance.
Product identity330180
Bently Nevada · 3300 XL 8 mm signal conditioning
Bently Nevada 330180-X1-00 MOD: 145004-09 | 3300 XL 8 mm Proximitor Sensor
Order fieldX1 retained
ApprovalNot required
Official product identity and signal path
Product Profile
Bently Nevada 330180-X1-00 MOD: 145004-09 is a 3300 XL 8 mm Proximitor Sensor that supplies excitation to a matched probe, receives the returned gap-dependent signal and converts it into a proportional voltage for the monitoring input. The sensor forms the electronics stage of the 3300 XL 8 mm proximity transducer chain.
At the field side, Bently Nevada 330180-X1-00 MOD: 145004-09 connects to a compatible 3300 XL 8 mm probe through the extension cable selected for the same total system length. Its output then travels on three-conductor shielded field wiring to the receiving monitor, with the sensor, probe and cable treated as one calibrated measurement path.
The final 00 approval field of Bently Nevada 330180-X1-00 MOD: 145004-09 specifies that agency approval is not required. The X1 field and MOD 145004-09 are retained exactly as supplied; no unsupported mounting style, system length or modification meaning is assigned on this page.
Verified configuration and operating values
Performance Specifications
Technical item330180-X1-00 MOD: 145004-09
BrandBently Nevada
Product Type3300 XL 8 mm Proximitor Sensor
Brand CountryUnited States
System family3300 XL 8 mm Proximity Transducer System
Base code 3301803300 XL 8 mm Proximitor Sensor
AA X1 — total length / mounting fieldRetained exactly as supplied; no unsupported meaning assigned
BB 00 — agency approval optionNot required
MOD 145004-09Modification reference retained exactly as supplied; no unsupported meaning assigned
System linear range2.0 mm (80 mil)
Nominal scale factor7.87 V/mm (200 mV/mil)
Frequency response0 to 10 kHz, +0/−3 dB typical
Power requirement−17.5 to −26 Vdc
Maximum current12 mA
Output resistance50 Ω
Minimum output load10 kΩ
Sensor operating temperature−52 to +100 °C
Sensor storage temperature−52 to +105 °C
Field wiringThree-conductor shielded triad
Maximum field-wiring distance305 m
Target basisAISI 4140 steel
Conditioned measurement output
Monitoring and Control
Bently Nevada 330180-X1-00 MOD: 145004-09 converts the probe response into the electrical signal used by the receiving monitor without performing the probe’s mechanical sensing role.
Proportional voltage conversion
Internal conditioning converts the returned high-frequency response into a voltage proportional to static gap and dynamic displacement within the system range.
Monitor-ready handoff
The low-impedance output is carried to the monitoring channel on shielded three-conductor wiring, where the configured monitor interprets the displacement signal.
Matched 8 mm signal chain
System Integration
Bently Nevada 330180-X1-00 MOD: 145004-09 operates with 3300 XL 8 mm probes and extension cables selected as a complete electrical length.
Probe, cable and conditioner remain one calibrated path
The probe creates the gap-dependent response, the extension cable completes the specified transducer length, and the Proximitor Sensor converts that response before field wiring carries it to the monitor.
Match the sensing components
Use a 3300 XL 8 mm probe and extension cable whose combined length corresponds to the Proximitor Sensor system length.
Connect the transducer side
Join the probe and extension-cable connectors cleanly and route the extension cable to the sensor input without substituting an unmatched cable family.
Complete the monitor wiring
Connect power, common and output through shielded three-conductor field wiring, keeping total distance within the stated 305 m boundary.
Exact-model product questions
Technical Questions
Why should Bently Nevada 330180-X1-00 MOD: 145004-09 not be ordered from the shortened 330180 family number alone?
Bently Nevada 330180-X1-00 MOD: 145004-09 contains an X1 field and a modification reference that are not resolved by the standard ordering table. Preserve the nameplate identifier and MOD reference so purchasing does not silently substitute a standard total-length or mounting execution.
What should be checked when Bently Nevada 330180-X1-00 MOD: 145004-09 powers up but the displacement scale is wrong?
Bently Nevada 330180-X1-00 MOD: 145004-09 must operate with a 3300 XL 8 mm probe and extension cable that form the intended complete electrical length. Check the probe part number and cable length together; a physically compatible but electrically mismatched cable changes the calibrated response.
How can a constant low or high output from Bently Nevada 330180-X1-00 MOD: 145004-09 be separated from an actual shaft-position problem?
For Bently Nevada 330180-X1-00 MOD: 145004-09, verify the probe gap and target first, then inspect the probe-to-extension-cable joints and measure the Proximitor Sensor output. This distinguishes a real gap condition from an open, shorted or mismatched transducer path.
What wiring mistake can leave Bently Nevada 330180-X1-00 MOD: 145004-09 with no usable monitor signal?
Bently Nevada 330180-X1-00 MOD: 145004-09 requires power, common and output on shielded three-conductor field wiring. Confirm the −17.5 to −26 Vdc supply polarity and keep the receiving load at or above 10 kΩ before treating the sensor as failed.
How should long field wiring from Bently Nevada 330180-X1-00 MOD: 145004-09 be evaluated?
Bently Nevada 330180-X1-00 MOD: 145004-09 permits up to 305 m of three-conductor shielded field wiring. Cable routing, shield continuity and receiving-input impedance still have to preserve the low-impedance output; the 305 m figure is not permission to mix the transducer extension cable with ordinary field wire.
Does the final 00 on Bently Nevada 330180-X1-00 MOD: 145004-09 prove that the installation has hazardous-area approval?
No. The final 00 on Bently Nevada 330180-X1-00 MOD: 145004-09 means agency approval is not required for that ordered execution. Approval suitability must not be inferred from the MOD number or from another 330180 variant.
Industrial parts coordination
Global Sourcing
Moore Automation
https://www.mvme.cn/Moore Automation sources industrial automation components for customers in different regions, including standard catalogue products and less common legacy references. Requests are checked by manufacturer, complete model and required quantity.
Where a model contains configurable suffixes, the supplied nameplate, ordering code or drawing stays attached to the sourcing record. This keeps the requested execution distinct from nearby variants during technical and commercial review.
Exact-model searchManufacturer and full suffix retained
Multi-brand requestsControl, drive and monitoring hardware
International handlingDestination and shipment details coordinated
www.mvme.cn
Sixty references across eight industrial brands
Compatible Products
- ABBACS355-03E-03A3-4
- Siemens6ES7195-7HD10-0XA0
- GEIS200TVBAS1ABB
- OmronC200H-OC222
- Schneider ElectricBMXNRP0200
- Mitsubishi ElectricFR-D720-0.75K-57
- HoneywellFC-BKM-0001
- SEW-EURODRIVEMC07B0008-5A3-4-00
- ABBACS355-03E-05A6-4
- Siemens6ES7505-0KA00-0AB0
- GEIS215UCVEH2AF
- OmronCS1W-INT01
- Schneider ElectricTM218LDA16DRN
- ABBACS355-03E-07A5-2
- Siemens6ES7590-1AC40-0AA0
- GEIS200TEFVH1AAD
- OmronNJ50-FP-A2
- Schneider ElectricTM30050
- ABBACS355-03E-09A8
- Siemens6ES7221-1BF22-0XA0
- GEIC695PBM300-CC
- OmronCPM6-SM336FAIH
- Schneider Electric140NOM21100
- ABBACS355-03E-13A3
- Siemens6AG1124-0GC13-2AX0
- GEIC693CHS397M
- OmronCS1W-ETN11
- Schneider ElectricTM2AMI2HTN
- ABBACS355-03E-17A6
- Siemens1FK7084-2AF71-1RG0
- GEIC693CHS392G
- OmronCJ1W-OD231
- Schneider Electric140DAO85300
- ABBACS355-03U-46A2-2
- Siemens6ES7132-4HB12-0AB0
- GEIC693CMM311H
- OmronCJ1W-TS561
- Schneider ElectricTM3-0515-C
- ABBACS510
- Siemens1FT7044-1AF70-1CG1
- GEIC694MDL740A
- OmronC500-CN511
- Schneider Electric140CPS22400
- ABBACS510-01-046A-4+B055
- Siemens1FK7060-2AF71-1QG1
- GEIC693CPU331J
- OmronC500-OC224-E
- Schneider ElectricA9MEM3165
- ABBDO526
- Siemens7KM9900-0YA00-0AA0
- GEIC693PWR321R
- OmronCJ1W-OD211
- Schneider Electric140XCP51000
- ABBPM573-ETH
- Siemens6FC5111-0CA01-0AA0
- GE44A726758-123R01
- OmronC200H-OD213
- Schneider ElectricTSXDEY16FK
- ABBACS150-03U-04A7-2
- Siemens6ES7390-5AA00-0AA0
Direct product enquiry channels
Request a Quote
Moore Automation
Connect with our team
Use the channels shown here for technical product and purchasing enquiries.
ManagerLeonia
Emailsales@mvme.cnWhatsApp+86 180 3017 5807
No related record found