Bently Nevada · 3300 XL 8 mm
Bently Nevada 330104-11-25-10-02-00 3300 XL 8 mm Metric Armored Proximity Probe
M10x1 metric probe with 110 mm unthreaded and 250 mm case lengths
Product Description
330104-11-25-10-02-00 is the armored M10x1 member of the Bently Nevada 3300 XL 8 mm probe family. The metric length fields specify 110 mm of unthreaded body, a 250 mm overall case and a 1.0 m integral lead.
Its miniature coaxial ClickLoc connector couples to a 3300 XL extension cable, and the completed chain terminates at a compatible 3300 XL Proximitor Sensor. The system output follows the probe-to-target gap so the monitor can process displacement, vibration, phase or speed information.
The long case configuration of 330104-11-25-10-02-00 provides reach through a bracket or casing while its stainless-steel armor shields the cable. Option 00 carries no selected agency approval.
Technical Specifications
| Technical Item | 330104-11-25-10-02-00 |
|---|---|
| Brand | Bently Nevada |
| Product Type | 3300 XL 8 mm metric armored proximity probe |
| Brand Country | United States |
| Probe Tip Diameter | 8.0 mm (0.31 in) |
| Case Thread | M10x1 |
| Unthreaded Length | 110 mm |
| Overall Case Length | 250 mm |
| Total Probe Length | 1.0 m (3.3 ft) |
| Lead Protection | Stainless-steel armor |
| Connector | Miniature coaxial ClickLoc, option 02 |
| Cable Type | Standard 75 Ω coaxial cable |
| Approval Option | 00 — not required |
| Maximum Thread Engagement | 15 mm |
| Minimum Cable Bend Radius | 25.4 mm (1.0 in) |
Metric Probe Construction
The 8 mm PPS tip and stainless-steel case form a non-contacting eddy-current sensing point, while the M10x1 body gives the probe a metric mounting interface. The 110 mm smooth section extends beyond the threaded mounting area, and the 250 mm case provides a controlled reach to the target.
Stainless-steel armor surrounds the 1.0 m lead. A ClickLoc connector at the cable end makes the probe removable from the extension cable without disturbing the Proximitor Sensor wiring.
3300 XL System Compatibility
3300 XL System Compatibility in practice
Use this probe with a 3300 XL extension cable and a 3300 XL 8 mm Proximitor Sensor configured for the same total system length. Within that product family, probes, extension cables and Proximitor Sensors are interchangeable without individual bench matching.
The 3300 XL 8 mm family is also backward compatible with non-XL 3300-series 5 mm and 8 mm system components under the stated family rules. It is not a direct member of the light-yellow 7200 5 mm/8 mm family, so a legacy 7200 loop should be reviewed as a complete chain before migration.
Frequently Asked Questions
What should be done if 330104-11-25-10-02-00 is too long or cannot reach the target after delivery?
Compare the installation with the ordered 110 mm unthreaded section and 250 mm overall M10x1 case before modifying any hardware. If the available bracket depth or casing clearance differs, select the correct length code instead of cutting or forcing the probe.
Can the existing extension cable be reused when replacing a probe with 330104-11-25-10-02-00?
Reuse is appropriate only when it belongs to the compatible 3300 XL 8 mm chain and the probe plus extension cable equals the Proximitor Sensor calibration length. Inspect and dry the ClickLoc interface, then verify the static gap output after connection.
How should intermittent readings from 330104-11-25-10-02-00 after washdown be investigated?
Moisture at the detachable coaxial interface can disturb the signal even though the probe lead is armored. Isolate the channel, open and dry the ClickLoc joint, inspect its protection and restore the connection before checking gap voltage again.
How can cable damage be prevented when installing the armored 330104-11-25-10-02-00?
Armor protects the lead but does not permit sharp bending, twisting or tensile load at the case. Maintain at least a 25.4 mm bend radius, clamp the route independently and leave enough slack for final probe adjustment.
Can 330104-11-25-10-02-00 replace a 7200-series probe without changing the rest of the loop?
Do not make a one-component substitution between these families. Confirm the probe, extension cable, Proximitor Sensor, total electrical length and monitor input as a complete system before planning a migration.
Our Services
Enquiry-to-delivery support
One account manager keeps the request clear from start to finish
A dedicated account manager reviews the requested brand, complete model and required condition before preparing the quotation. The same contact follows availability, lead time, shipping arrangements and tracking information, reducing hand-offs during an urgent spare-parts purchase.
Support covers both routine enquiries and difficult searches for discontinued industrial automation components.
No related record found