Bently Nevada3300 XL 8 mm Proximity Transducer System

Bently Nevada 330101-00-32-10-01-00 | 3300 XL 8 mm 3/8-24 UNF Proximity Probe

Name: Bently Nevada 330101-00-32-10-01-00 | 3300 XL 8 mm 3/8-24 UNF Proximity Probe
Brand: Bently Nevada
SKU: 2929819
Price: 1 USD
Availability: InStock

Record01

Product Overview

The sensing end of a standard 8 mm transducer system is Bently Nevada 330101-00-32-10-01-00, a 3/8-24 UNF proximity probe without armor. It converts shaft-to-tip distance change into the raw probe response carried to the matched extension cable and Proximitor Sensor.

For 330101-00-32-10-01-00, code 00 selects no unthreaded section and code 32 selects a 3.2 in case. The 1.0 m total-length selection ends in the standard miniature connector with its protector, giving the connector a defined mechanical cover before it joins the extension cable.

Approval option 00 states that no agency-approval selection is included. The probe remains part of the 3300 XL 8 mm calibrated system, so the installed probe length, extension cable and Proximitor Sensor must preserve the ordered system length.

Bently Nevada 3300 XL 8 mm proximity probe technical drawing

Data02

Product Data

Technical item	Specification
Brand	Bently Nevada
Model	330101-00-32-10-01-00
Product Name	3300 XL 8 mm proximity probe
Country	United States
System Family	3300 XL 8 mm Proximity Transducer System
Thread	3/8-24 UNF-2A
Armor	Not included
Unthreaded Length	0.0 in
Overall Case Length	3.2 in
Total Probe Length	1.0 m
Connector	Miniature coaxial connector
Connector Protector	Included
Cable Type	Standard cable
Agency Approval	Not selected
System Linear Range	2.0 mm
System Scale Factor	7.87 V/mm nominal
Recommended Gap	1.27 mm
Frequency Response	0 to 10 kHz typical

Focus03

System Integration

Probe connection

The probe is the first element of a matched electrical-length chain rather than a standalone voltage sensor. The guidance below explains how the complete 330101-00-32-10-01-00 record is applied in the installed assembly rather than repeating isolated catalogue values.

Probe connection

Protect the miniature connector and keep it free of contamination before mating it to the extension cable. Document the upstream and downstream interfaces so 330101-00-32-10-01-00 remains identifiable in the complete path.

Matched length

Confirm that probe plus extension-cable length equals the length required by the selected Proximitor Sensor. Check the physical connection first, then confirm that the signal reaches the intended channel for 330101-00-32-10-01-00.

Monitor output

Land the conditioned Proximitor output and common at the monitor without confusing them with the probe-side coaxial path. Retain the connected-component references with 330101-00-32-10-01-00 for commissioning and later fault tracing.

Focus04

Installation Highlights

Prepare the 3/8-24 mount

Mechanical preparation sets the probe axis and protects the cable before the electrical gap is adjusted. The guidance below explains how the complete 330101-00-32-10-01-00 record is applied in the installed assembly rather than repeating isolated catalogue values.

Path 01

Prepare the 3/8-24 mount

Align the threaded opening with the target and preserve side clearance around the sensing tip. Before closure, record the final position and hardware state for 330101-00-32-10-01-00.

Identify the exact 330101-00-32-10-01-00 interface before work begins.

Trace the connected mechanical or electrical path.

Record the verified condition before commissioning.

Path 02

Route the unarmored lead

Provide bend relief and protection so the standard cable is not pulled at the probe case. After the mechanical work, verify cable freedom and the measurement gap for 330101-00-32-10-01-00.

Keep the 330101-00-32-10-01-00 channel and component references together.

Confirm the next device or machine boundary in the path.

Test the completed connection under its intended condition.

Path 03

Gap after locking

Set the nominal gap, secure the mounting hardware and recheck the dc gap voltage after tightening. Finish with an inspection record that ties the mounted assembly back to 330101-00-32-10-01-00.

Preserve the complete 330101-00-32-10-01-00 identifier in the work record.

Separate mounting, wiring and signal checks during diagnosis.

Hand over the final result with the installed configuration.

Help05

Questions About This Product

How is the selected length represented in 330101-00-32-10-01-00?

The cable-length field within 330101-00-32-10-01-00 is part of the exact probe record. Preserve it when matching the extension cable so probe plus extension equals the Proximitor Sensor system length.

What should be checked at the 3/8-24 mounting point for 330101-00-32-10-01-00?

For 330101-00-32-10-01-00, confirm thread condition, probe-axis alignment and clearance around the sensing tip. Tightening an off-axis case can move the tip away from the intended target.

How should the unarmored lead on 330101-00-32-10-01-00 be protected?

Route 330101-00-32-10-01-00 with strain relief, bend protection and separation from sharp or vibrating structures. The standard lead should not carry the mechanical load of the cable run.

What does the miniature connector require during installation of 330101-00-32-10-01-00?

Keep the 330101-00-32-10-01-00 connector clean, fully seat the ClickLoc joint and protect it before fixing the remaining extension-cable route. Contamination or partial engagement can imitate a probe fault.

How is a bad gap distinguished from a bad cable on 330101-00-32-10-01-00?

With 330101-00-32-10-01-00 connected to the correct sensor, compare supply and dc gap voltage while checking cable continuity and target position. Separate mechanical movement from open/short conditions before replacing the probe.

Which order information prevents a mismatch for 330101-00-32-10-01-00?

State 330101-00-32-10-01-00, quantity, total system length, thread, lead type and approval requirement. Do not reduce the request to 3300 XL 8 mm because that hides the selected construction.

Moore06

Customer Support

Moore Automation

https://www.mvme.cn

Customer support keeps the complete model, requested quantity and the customer question in one communication path. Available records can be coordinated so technical clarification does not become separated from the enquiry.

Question intakeModel-specific questions remain explicit.

Reference checkThe complete article string stays visible.

Document follow-upAvailable files can be coordinated.

Contact continuityOne contact supports further discussion.

Catalogue07

Related Products

Bently Nevada3500/32M 125720-02

TRICONEX4610

HIMAF8650X、F7131、F3330、F3236、F3237、F6217 F3349 F8650X

EmersonVE3011

B&R5PC910.SX05-00

ABBPM564-RP-AC

TRICONEX3723X

TRICONEX9666X

TRICONEX8107X

TRICONEX8108X

TRICONEX8109X

TRICONEX8120

TRICONEX8311

ABBPM5630-2ETH-XC

Allen-Bradley5069-L330ERMS2

Bently Nevada3500/46M

EmersonKJ1501X1-BC2

HIMAF8652X

HoneywellCC-TCNT02

MotorolaMVME61006E-0161

Siemens6ES7512-1DK01-0AB0

TRICONEX3401S2

ABBPM581-ETH

Allen-Bradley1756-L902TS

Bently Nevada3500/72M 176449-08

HoneywellCC-GAIX21

Allen-Bradley1756-IB16D

HIMAF3322

Allen-Bradley1756-IF16

Siemens6ES7518-4FX00-1AC0

HIMAF6706

HIMAF-BASE RACK 01

HIMAF9203A

HIMAX-COM 01

HIMAX-PS 01

HIMAX-DI 32 01

HIMAX-DO 32 01

HIMAX-AI 32 01

HIMAX-AO 16 01

HIMAX-CI 24 51

ABBPM5072-T-2ETHW

ABBCM575-DN

Bently Nevada330780-90-CN

Siemens6ES7505-0RA00-0AB0

ABBTB511-ETH

Bently Nevada990-04-70-01-01

Siemens6ED1052-1CC08-0BA2

ABBTK-PRR021

Bently Nevada991-25-70-01-00

Siemens6ED1055-1MA00-0BA2

ABBCI862K01

Bently Nevada60R/PIM01-02-0

Siemens6EP3332-6SB00-0AY0

Bently Nevada60X/XPS01-01

Bently Nevada3701/46

Bently Nevada330851-01-000-020-10-00-00

Bently Nevada330878-90-00

Bently NevadaADRE 408 DSPi 168679-01-01-01-02-03-05-01-01-00-02-02

Bently Nevada9200-09-01-06-04

Bently Nevada330103-0-10-10-01-00

Contact08

Contact Information

Moore AutomationSend the complete model and requested quantity.

ManagerLeonia

Emailsales@mvme.cn

WhatsApp+86 180 3017 5807

Product Name	Bently Nevada 330101-00-32-10-01-00 \| 3300 XL 8 mm 3/8-24 UNF Proximity Probe
Item NO.	2929819
Weight	0.1 kg = 0.2205 lb = 3.5274 oz
Category	BENTLY NEVADA
Brand	Bently Nevada
Creation Time	2026-11-04

Bently Nevada 330101-00-32-10-01-00 | 3300 XL 8 mm 3/8-24 UNF Proximity Probe Item NO.: 2929819