Linear target response
Across the 2.0 mm linear span, the system output changes at a nominal 7.87 V/mm. This lets the receiving monitor relate voltage change to displacement or vibration.
Product identity330101
Bently Nevada · 3300 XL 8 mm proximity system
Bently Nevada 330101-00-20-05-02-00 | 3300 XL 8 mm Proximity Probe
Thread3/8-24 UNF
Lead0.5 metre
Official product identity and signal path
Hardware Overview
Bently Nevada 330101-00-20-05-02-00 is a standard-mount 3300 XL 8 mm proximity probe with a 3/8-24 UNF threaded case and no armor. It senses radial vibration or axial position by changing its electrical response as the conductive target moves relative to the 8 mm tip.
The order fields of Bently Nevada 330101-00-20-05-02-00 define a zero-inch unthreaded section, a 2.0-inch case and a 0.5 m total probe length. Its standard ClickLoc cable ending connects to the extension cable selected so that probe and extension length equal the associated Proximitor Sensor length.
Within the complete 3300 XL path, Bently Nevada 330101-00-20-05-02-00 operates with the matched 8 mm extension cable and Proximitor Sensor. The sensor excites the probe, conditions the returned eddy-current response and passes a proportional voltage to the monitor.
Verified configuration and operating values
Engineering Data
Technical item330101-00-20-05-02-00
BrandBently Nevada
Product Type3300 XL 8 mm proximity probe
Brand CountryUnited States
System family3300 XL 8 mm
Base code 3301013/8-24 UNF thread; without armor
AA 00 — unthreaded length0.0 in
BB 20 — overall case length2.0 in
CC 05 — total probe length0.5 m
DD 02 — connector and cableStandard miniature coaxial ClickLoc; standard cable
EE 00 — approval optionNo agency approval option
Probe tip diameter8.0 mm
Linear range2.0 mm (80 mil)
Recommended radial gap1.27 mm (50 mil)
Scale factor7.87 V/mm (200 mV/mil), ±5% for 1 m/5 m systems
Frequency response0 to 10 kHz, +0/−3 dB typical
Probe case materialAISI 303 or 304 stainless steel
Probe tip materialPolyphenylene sulfide
Probe temperature−52 to +177 °C
Cable construction75 Ω triaxial, FEP insulated
Field wiringThree-conductor shielded triad, up to 305 m
System supply−17.5 to −26 Vdc; 12 mA maximum
Measurement behavior
Performance Characteristics
The configured 3300 XL components around Bently Nevada 330101-00-20-05-02-00 translate target motion into a predictable voltage over the standard 8 mm measurement envelope.
Broad dynamic bandwidth
The standard system maintains a typical +0/−3 dB response from dc through 10 kHz when field wiring remains within the stated length.
Stable matched components
Probe, extension cable and Proximitor Sensor are designed as electrically and physically matched 3300 XL components, limiting interchangeability error within the stated system conditions.
Compatible signal chain
System Integration
Bently Nevada 330101-00-20-05-02-00 occupies the machine-side end of a 3300 XL 8 mm measurement chain.
Probe → extension cable → Proximitor
The probe detects the target, the extension cable completes the calibrated electrical length, and the 3300 XL 8 mm Proximitor Sensor converts the response for the monitor.
Machine interface
The 3/8-24 case threads into the prepared mounting point while the 8 mm tip faces the conductive shaft or target.
Matched cable path
The 0.5 m probe cable joins a 3300 XL 8 mm extension cable through its standard ClickLoc connector.
Monitor connection
Three-conductor shielded field wiring carries the Proximitor output to the receiving monitor; the shield and wiring length remain part of the installed signal path.
Exact-model product questions
Buyer Questions
How can a buyer confirm that Bently Nevada 330101-00-20-05-02-00 will reach the target without over-inserting the probe?
Bently Nevada 330101-00-20-05-02-00 combines a 2.0-inch threaded case with zero unthreaded length. Compare the mounting-bracket thickness, available thread engagement and required 1.27 mm reference gap before ordering; the 330101 family name by itself does not confirm the installed reach.
Why might Bently Nevada 330101-00-20-05-02-00 give a biased or compressed displacement signal?
Bently Nevada 330101-00-20-05-02-00 must face the specified conductive target within the 2.0 mm linear range. Check target geometry, probe alignment and the set gap first, because an off-axis face or a gap near the range boundary can consume usable measurement travel before shaft motion is applied.
What must match when replacing only Bently Nevada 330101-00-20-05-02-00 in an existing 3300 XL 8 mm chain?
Bently Nevada 330101-00-20-05-02-00 has a 0.5 m integral lead and must remain paired with an extension cable and Proximitor Sensor selected for the same complete system length. Reusing an electrically mismatched cable can change the scale even though every ClickLoc connector mates.
How should a no-signal complaint on Bently Nevada 330101-00-20-05-02-00 be isolated?
For Bently Nevada 330101-00-20-05-02-00, inspect the unprotected DD 02 ClickLoc connection, verify continuity through the matched extension cable, then confirm Proximitor Sensor power and output. This sequence avoids replacing the probe when the interruption is at the connector or conditioner.
What installation issue can make Bently Nevada 330101-00-20-05-02-00 report vibration that is not actual shaft motion?
If Bently Nevada 330101-00-20-05-02-00 is not locked squarely to the target or the cable loads the probe body, mechanical movement at the mounting point can alter the apparent gap. Secure the threaded case after setting the gap and strain-relieve the 0.5 m lead.
Why is the full suffix needed when requesting Bently Nevada 330101-00-20-05-02-00?
The suffix of Bently Nevada 330101-00-20-05-02-00 fixes the 2.0-inch case, 0.5 m lead, standard unprotected ClickLoc and no-approval execution. Supplying only 330101 leaves several mechanically and electrically different order fields unresolved.
Practical customer support
Our Advantages
Moore Automation
https://www.mvme.cn/Moore Automation combines multi-brand industrial sourcing with model-led enquiry handling. Complete order numbers, suffixes and modification references remain visible so customers can compare the requested item with the available product record.
Support also extends to discontinued and difficult-to-source components, with product images and available technical material kept alongside the enquiry instead of relying on a shortened family name.
Exact identifiersFull model and ordering-code records
Technical coordinationAvailable drawings, manuals and product data
Hard-to-find supportCurrent, legacy and discontinued references
www.mvme.cn
Sixty references across eight industrial brands
Alternative Models
- ABBACS510-01-038A-4+B055
- Siemens6ES7131-1BL01-0XB0
- GEIC670GBI002H
- OmronCJ2MCPU1122
- Schneider ElectricTSXDSY16T2
- Mitsubishi ElectricFX4S-1P2
- HoneywellDC-TFB412
- Rockwell Automation1746-N2
- ABBCI592-CS31
- Siemens6ES7195-7HA00-0XA0
- GEIC200CPUE05
- OmronNJ10-30GK-SN
- Schneider ElectricA9MEM3200
- ABBPM5630-2ETH
- Siemens6ES7392-1BN00-0AA0
- GEIC200UEX014-B
- OmronC5000
- Schneider ElectricVW3M3619
- ABBACS150-03E-05A6-4
- Siemens6FX5002-2DC30-1BH0
- GEIC200UAA003-AA
- OmronNJ5-18GK-E2
- Schneider Electric140M-C2N-B10
- ABBACS355-03E-31A0-4
- Siemens1FK7101-2AF71-1RG0
- GEIC693ALG390C
- OmronCQM1-CPU45-EV1
- Schneider ElectricTM200
- ABBACS355-03U-02A4-4
- Siemens1FT6084-1AF71-1FH1
- GEIC693MDL330G
- OmronCS1W-CT021
- Schneider ElectricTSXP575634M
- ABBACS355-03U-04A7-2
- Siemens6ES7214-1KF40-0XB0
- GEIS200ECTBG2A-DE
- OmronCJ1W-MD231
- Schneider ElectricTSXMCPC002M
- ABBACS355-03U-12A5-4
- Siemens1FK7086-7AF71-1FH0
- GEIS220PRTDH1B
- OmronCJ1W-OD201
- Schneider ElectricBMXCPS4002S
- ABBDI562
- Siemens6ES7513-1FL02-0AB0
- GEIS220PPROS1B
- OmronC500-PRO13
- Schneider ElectricBMXXBP0800H
- ABBPM564-TP-ETH
- Siemens6GK7545-1GX00-0XE0
- GEIS220PDIOH1B
- OmronCQM1H-PLB21
- Schneider ElectricTSXP57203M
- ABBACS150-03E-09A8-2
- Siemens6ES5150-3XB00R
- GEIC754VSF
- OmronCJ2M-MD212
- Schneider ElectricBMXP342020
- ABBACS180-04N-09A8-1
- Siemens6SL3000-0BE23-6AA0
Direct product enquiry channels
Get in Touch
Moore Automation
Connect with our team
Use the channels shown here for technical product and purchasing enquiries.
ManagerLeonia
Emailsales@mvme.cnWhatsApp+86 180 3017 5807
No related record found