Welcome to Moore Automation Limited
|
Copy and share this link on social network or send it to your friends
Copy| Product Name | Bently Nevada 102044-00-32-10-02 Legacy 8 mm Proximity Probe |
| Item NO. | 2908459 |
| Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
| Category | BENTLY NEVADA |
| Brand | Bently Nevada |
| Creation Time | 2026-09-15 |
Bently Nevada · Legacy 8 mm Probe
Full coded configuration retained for a matched machinery-monitoring loop
102044-00-32-10-02 is a Bently Nevada legacy 8 mm proximity-probe configuration. The full code identifies a 0.0 in unthreaded length, a 3.2 in overall case, a 1.0 m total lead and a miniature male coaxial connector.
The probe senses the changing gap to a conductive target and passes that signal through its matched extension cable to the associated Proximitor Sensor. Static position and dynamic shaft-vibration functions are determined by the mounting direction and monitor setup.
Keep every suffix with 102044-00-32-10-02 during replacement. Mechanical similarity alone does not establish electrical compatibility with a 7200, 3300 or 3300 XL chain.
| Technical Item | 102044-00-32-10-02 |
|---|---|
| Brand | Bently Nevada |
| Product Type | Legacy 8 mm proximity probe |
| Brand Country | United States |
| Probe Tip Diameter | 8 mm |
| Unthreaded Length | 0.0 in |
| Overall Case Length | 3.2 in |
| Total Probe Length | 1.0 m (3.3 ft) |
| Connector | Miniature male coaxial, option 02 |
| Signal Principle | Non-contacting eddy current |
| Measured Quantity | Static gap and dynamic displacement |
| Target | Conductive machine surface |
| System Requirement | Matched extension cable and Proximitor Sensor |
When installed radially, the probe supplies shaft-relative vibration and static shaft-position information from fluid-film bearing machinery. An axial mounting can support thrust-position or differential movement measurements when the receiving channel is configured for that geometry.
A phase-reference or speed point is also possible when the probe views a suitable keyway or projection. In every case, the target, gap range and monitoring channel must remain consistent with the installed transducer family.
The 3.2 in case establishes the probe reach while the 0.0 in unthreaded option keeps the body threaded to the sensing end. The 1.0 m integral cable terminates in a miniature male coaxial connector for attachment to the installed extension cable.
Confirm the mounting thread from the nameplate and machine drawing before installation. Secure the cable against motion, protect the coaxial joint from liquids and set the final gap using the matched Proximitor Sensor output rather than a mechanical distance estimate.
Use the full suffix to compare the 0.0 in unthreaded section, 3.2 in case, 1.0 m lead and miniature male coaxial connector. Also identify the installed extension cable and Proximitor Sensor because mechanical dimensions alone are not enough.
Similar tips can belong to different Bently Nevada transducer families with different electrical lengths and electronics. Match the case, connector, cable length, transducer family and monitor input before approving a substitute.
Verify that the tip views the intended conductive target and that the probe has not been set outside its usable gap. Inspect the coaxial joint and matched electronics, then adjust the gap using the live output rather than a visual estimate.
Mount it radially toward the shaft for shaft-relative vibration; use an axial orientation for thrust or position measurement. Confirm the receiving channel is configured for the selected measurement before enabling alarms.
Confirm the thread and available case clearance from the installed point before forcing the probe into a bracket. Preserve the 3.2 in case reach, support the 1.0 m cable and set the final gap only after the mechanical fit is correct.
Legacy-system continuity
Moore Automation specializes in sourcing discontinued, obsolete and scarce industrial automation parts. Continued access to replacement PLC, DCS, HMI, drive, sensor and monitoring components can help users maintain established systems and avoid unnecessary platform replacement.
The complete brand and model are kept with the enquiry so legacy variants with similar base numbers remain clearly separated.
Moore Automation Sales Team
Copyright © 2004–2026 www.mvme.cn. All rights reserved.
Disclaimer: Moore Automation Limited is an independent reseller and is not an authorized distributor or representative of the manufacturers featured on this website. Product names and trademarks belong to their respective owners.
No related record found