ABB · AC500-XC V3PM5630Extreme-Condition Processor Module

R03xx AC500-XC V3 identity

ABB PM5630-2ETH-XC 1SAP331000R0378 Extreme-Condition Processor Module

An AC500-XC V3 processor with dual configurable Ethernet, serial and CAN interfaces, 8 MB total user memory and a dedicated XC terminal-base requirement.

Product Introduction

ABB PM5630-2ETH-XC 1SAP331000R0378 is an AC500-XC V3 processor module for control stations that need extended-condition hardware and multiple integrated communication paths. Its 300 MHz ARM Cortex-A9 processor works with 128 MB RAM and 128 MB flash while the controller exposes two Ethernet interfaces, one configurable serial interface and one CAN interface.

The CPU provides 8 MB total user-program memory, including 1 MB for user program code and data, with a maximum downloadable application size of 9 MB and up to 6 MB for web data. The dual Ethernet interfaces can be configured for supported industrial protocols, while the serial and CAN paths integrate devices that do not use Ethernet.

Order code 1SAP331000R0378 identifies the R03xx product revision of ABB PM5630-2ETH-XC 1SAP331000R0378. It requires Automation Builder 2.6.0 or later and firmware 3.6.0 or later, cannot be downgraded below those versions, and must be used with the dedicated TB56xx-2ETH-XC terminal-base family.

ABB PM5630-2ETH-XC AC500-XC V3 processor module catalog view

Technical Information

Brand	ABB
Model	PM5630-2ETH-XC 1SAP331000R0378
Product name	AC500-XC V3 Processor Module
Country	Germany / Finland
CPU	ARM Cortex-A9, 32-bit RISC
Clock frequency	300 MHz
Total user memory	8 MB
Program code and data	1 MB
RAM / flash	128 MB / 128 MB
Ethernet	2 configurable interfaces
Serial interface	1 × RS232 / RS485
CAN interface	1 integrated
Supply voltage	24 V DC via terminal base
Required terminal base	TB56xx-2ETH-XC family
Net weight	Approx. 0.137 kg

Network Capabilities

ABB PM5630-2ETH-XC 1SAP331000R0378 integrates Ethernet, serial and CAN paths, but each interface still needs a defined operational role.

Dual Ethernet

Assign protocols and network boundaries

The two independent Ethernet interfaces can support configurable protocols and switching functions. Document the protocol license, address, redundancy or separation purpose for each port so maintenance does not bridge networks unintentionally.

Serial channel

Match electrical mode and framing

The internal serial interface is configurable for RS232 or RS485 operation and supported ASCII or Modbus RTU roles. Cable pinout, termination, baud rate, parity and master/slave selection must all agree with the connected device.

CAN integration

Control bus topology from end to end

The integrated CAN interface supports documented CAN-based protocols. Verify bitrate, node addressing, cable impedance and termination at the physical ends, because a healthy CPU cannot compensate for an incorrectly terminated trunk.

Lifecycle and Upgrade

The R03xx generation of ABB PM5630-2ETH-XC 1SAP331000R0378 has explicit engineering, firmware and terminal-base dependencies that belong in every replacement plan.

Use Automation Builder 2.6.0 or later

Open and validate the project with a supported Automation Builder release before the shutdown. Keep an untouched backup, resolve library changes deliberately and document the converted project version used for commissioning.

Maintain version 3.6.0 or later

The R03xx CPU requires firmware 3.6.0 or higher and cannot be downgraded below that baseline. Check option, protocol and project compatibility before updating rather than using firmware changes as a general troubleshooting step.

Install only the dedicated XC base family

PM5630-2ETH-XC uses TB56xx-2ETH-XC bases: TB5600 for zero option slots, TB5610 for one and TB5620 for two. The selected base determines expansion capacity and must match the project and physical communication modules.

Frequently Asked Questions

Why will a project not download to ABB PM5630-2ETH-XC 1SAP331000R0378 after replacement?

ABB PM5630-2ETH-XC 1SAP331000R0378 R03xx requires Automation Builder 2.6.0 or later and firmware 3.6.0 or later. Confirm the exact order code, hardware entry, firmware, libraries and terminal-base configuration before retrying the download.

Can ABB PM5630-2ETH-XC 1SAP331000R0378 use an older non-XC terminal base?

No generic substitution should be made. ABB PM5630-2ETH-XC 1SAP331000R0378 is specified for the TB56xx-2ETH-XC family; select TB5600, TB5610 or TB5620 according to the required option-slot count.

Why does one Ethernet interface of ABB PM5630-2ETH-XC 1SAP331000R0378 work while the second remains offline?

Check the second interface configuration, licensed protocol, IP settings, cable and external switch path on ABB PM5630-2ETH-XC 1SAP331000R0378. Treat the ports as separately assigned resources rather than assuming that one port automatically mirrors the other.

What should be checked for serial communication failure on ABB PM5630-2ETH-XC 1SAP331000R0378?

On ABB PM5630-2ETH-XC 1SAP331000R0378, verify RS232 versus RS485 mode, pinout, termination, baud rate, parity, message role and device address. Capture traffic where possible before changing multiple parameters at once.

How should ABB PM5630-2ETH-XC 1SAP331000R0378 be prepared for a firmware update?

Back up the ABB PM5630-2ETH-XC 1SAP331000R0378 project and data, record the current firmware and communication settings, confirm power stability and review compatibility of libraries, options and protocols. Follow a controlled rollback plan that respects the 3.6.0 minimum.

What information is essential when ordering ABB PM5630-2ETH-XC 1SAP331000R0378?

Provide ABB PM5630-2ETH-XC 1SAP331000R0378 in full, the installed TB56xx-2ETH-XC base, option-slot requirement, Automation Builder version, firmware and interface use. This prevents confusion with earlier R02xx or classic-phase product records.

Company Profile

Moore Automation

https://www.mvme.cn

Moore Automation supplies industrial automation components with emphasis on complete product identification and practical enquiry handling. Manufacturer, model, order code, quantity and destination are retained together from the first request.

For ABB PM5630-2ETH-XC 1SAP331000R0378, revision, engineering baseline and terminal-base requirement can be recorded before the commercial response, giving technical and purchasing teams one consistent product description.

Identity firstRevision and order code preserved

System contextBase and options included

Global coordinationDestination planned with request

Selected Products

Contact & Enquiry

Confirm the R03xx CPU and terminal base

ManagerLeonia

Emailsales@mvme.cn

WhatsApp+86 180 3017 5807

Product Name	ABB PM5630-2ETH-XC 1SAP331000R0378 Extreme-Condition Processor Module
Item NO.	2931706
Weight	0.1 kg = 0.2205 lb = 3.5274 oz
Category	ABB
Brand	ABB
Creation Time	2026-11-11

ABB PM5630-2ETH-XC 1SAP331000R0378 Extreme-Condition Processor Module Item NO.: 2931706