ABBRobotics

ABB 3HAC031683-001 10 m FlexPendant Cable

3HAC031683-001Technical record

Product Overview

ABB 3HAC031683-001 is a 10 m FlexPendant cable listed for the IRC5 Panel Mounted controller. It carries the operator-terminal connection between the controller and the pendant and must remain identified separately from the complete FlexPendant assembly.

When ABB 3HAC031683-001 is routed through a robot cell, connector seating, mechanical protection and freedom from moving equipment determine whether the communication path remains stable. The cable length should be planned before the holder position is fixed so excess cable is not left in a pinch or traffic zone.

A replacement request for ABB 3HAC031683-001 should preserve the exact article, the 10 m length and the installed controller context. Commissioning then checks the pendant connection and emergency-stop chain through the approved IRC5 restart procedure rather than treating the cable as a passive generic lead.

Technical Specifications

Brand: ABB
Product Name: 10 m FlexPendant cable
Country: Switzerland
Product Category: Operator-interface cable
Controller Platform: IRC5 Panel Mounted
Cable Length: 10 m
Connected Device: FlexPendant operator terminal

Connection Role: Controller-to-pendant communication and safety path
Installation Form: Flexible cell cable route
Routing Requirement: Keep clear of robot motion, sharp edges and pinch points
Connector Check: Inspect, align and seat both ends before energizing
Commissioning Check: Verify pendant recognition and emergency-stop path
Order Identity: Cable article only; not the complete pendant
Manual Record: IRC5 Panel Mounted spare-parts list

Communication and Connectivity

ABB 3HAC031683-001 forms the physical link used by the FlexPendant, so a reliable installation depends on connector condition, cable routing and an intact controller-side path rather than cable length alone.

Preserve connector identity

Label both ends of ABB 3HAC031683-001 before removal and compare the controller-side and pendant-side connectors with the installed route.

Control the moving path

Route ABB 3HAC031683-001 outside robot envelopes, doors and sharp cabinet edges; support the cable without creating tension at either connector.

Prove the complete link

After ABB 3HAC031683-001 is connected, confirm pendant recognition and perform the approved safety-chain verification before returning the cell to operation.

Installation Highlights

Installing ABB 3HAC031683-001 is a sequence of isolation, route planning, connector inspection and controlled restart. The work should protect the cable mechanically while preserving the exact IRC5 connection record.

Plan before fastening

Lay out ABB 3HAC031683-001 from the controller to the operating position and confirm that the 10 m route reaches without an extension or strained bend.

Inspect and seat

With power isolated, check both connector faces, align the keys and seat ABB 3HAC031683-001 without twisting the shell or loading the pins.

Restart deliberately

Secure the route, remove temporary loops from walkways and complete pendant, emergency-stop and controller-status checks under the site procedure.

Frequently Asked Questions

Why is the FlexPendant intermittently disconnecting after ABB 3HAC031683-001 was installed?

For ABB 3HAC031683-001, inspect both connectors, unsupported bends and any section exposed to robot motion; then verify pendant recognition while the cable is moved only within its intended route.

Can ABB 3HAC031683-001 be treated as a complete FlexPendant order?

No. ABB 3HAC031683-001 identifies the 10 m FlexPendant cable, so the request must state separately if the handheld pendant or holder hardware is also required.

Which route records prevent a reconnecting error when ABB 3HAC031683-001 is removed?

Photograph the controller connection, pendant connection and cable route for ABB 3HAC031683-001, and retain the controller and cell identification with the article record.

How should excess ABB 3HAC031683-001 cable be managed?

Keep excess ABB 3HAC031683-001 outside pinch points and robot envelopes, use a supported service loop, and avoid tight coils that load the connectors.

Why must the safety path be checked after changing ABB 3HAC031683-001?

ABB 3HAC031683-001 carries the pendant connection used in the operator and emergency-stop chain, so controlled safety verification is required before production resumes.

Which site details prevent an incomplete quotation for ABB 3HAC031683-001?

Include ABB 3HAC031683-001, the required quantity, IRC5 controller context, existing cable condition and destination so the request remains specific.

Company Profile

Moore Automation

https://www.mvme.cn/

Moore Automation keeps complete industrial-automation article references, requested quantities and available records together in one enquiry. ABB robot parts are reviewed by their full article identity so similar mechanical and electrical assemblies remain distinguishable.

Exact identityFull ABB article stays visible

Document routeAvailable records follow the request

Request scopeQuantity and destination stay linked

Direct contactOne named contact supports follow-up

Contact Information

Send the complete model and quantity.

ManagerLeonia

Emailsales@mvme.cn

WhatsApp+86 180 3017 5807

Product Name	ABB 3HAC031683-001 10 m FlexPendant Cable
Item NO.	2930080
Weight	0.1 kg = 0.2205 lb = 3.5274 oz
Category	ABB
Brand	ABB
Creation Time	2026-11-05

ABB 3HAC031683-001 10 m FlexPendant Cable Item NO.: 2930080

ABB 3HAC031683-001 10 m FlexPendant Cable

Product Overview

Technical Specifications

Communication and Connectivity

Communication and Connectivity

Preserve connector identity

Control the moving path

Prove the complete link

Installation Highlights

Installation Highlights

Plan before fastening

Inspect and seat

Restart deliberately

Frequently Asked Questions

Company Profile

Moore Automation

Recommended Products

Contact Information

You May Also Like

Recently Viewed